NEC Itl12d1 User Guide

 24 
1.
CONDITIONS FOR DT700 SERIESPlease note that following terminal settings (by Feature
Key + Digit Key) cannot be used for DT700 Series.
•Feature +0  =Side Tone On/Off (for handset)
For the settings, contact to the Administrator.
* Uses can confirm the settings in “Audio&Visual Set-
tings”  →  “Side Tone Volume” of Online Monitoring.
• Feature +2  =Adjusts handset receiver volume
For the settings, contact to the Administrator.* Users can confirm the settings in “Audio&Visual Set-
tings”  → “Audio...

 25 
2.
I
NSTALLATION
 P
ROCEDURE
ADJUSTING ANGLE OF TILT LEG 
 
 
The angle of the tilt leg can be adjusted in four levels.• TO RAISE TILT LEGSTEP 1: Turn the telephone set upside down. 
STEP 2: Adjust the tilt leg in the direction of the arrow
until you hear it click. 
• TO LOWER TILT LEGSTEP 1: Turn the telephone set upside down. 
STEP 2: While lifting the center of the stopper, adjust the tilt leg in the direction of the arrow until
you hear it click.
DT730/710
DT330/310
First Level
Second Level...

 26 
TO REMOVE TILT LEG
 
STEP 1: Turn the telephone set upside down. 
STEP 2: Lower the tilt leg to first level.
STEP 3: Remove the indicated portions (a and b) ofthe stopper from grooves (A and B) on the tilt
leg and then widen the tilt leg. 
STEP 4: While pushing the two  hooks, slide the tilt leg
downward. Remove the tilt leg from the termi-
nal.
T O  AT TA C H  T I LT  L E G
 
STEP 1: Turn the telephone set upside down. 
STEP  2: Align the hooks (c-h) of the tilt leg over the ap- propriate slots...

 27 
CONNECTING LAN CABLESTEP 1: Prepare 10 BASE-T/100 BASE-T/TX cables(Straight) for connecting the telephone to net-
work device such as HUB, PoE Switch.
STEP 2: Connect the telephone to the network device using the LAN cable.
STEP 3: Thread the LAN cable through the groove on the back of the telephone.
STEP 4: When AC adapter is used to supply power to the telpehone, connect the AC/DC adapter to
the telephone as shown below.DT730/710
Telephone To LAN
Groove
LAN Straight Cable To PC
Telephone
AC...

 28 
CONNECTING LINE CORD STEP 1: Insert Line cord plug into Line connector onthe back of the telephone set until you hear it
clicks.
STEP 2: Thread the line cord through the groove on the back of the telephone.
STEP 3: Lead the line cord out through the groove on the tilt leg as shown in the figure below.DT330/DT310
Line Cord Line Cord Plug
Line Connecto
r
Telephone
Line Code
Groove
Telpehone
Tilt Leg
Groove Line Cord  

 29 
INSTALLING DIRECTORY CARDV
 
 
A directory card (also known as an abbreviated dialing
table) can be attached to the telephone sets. The
directory card can be used to record often dialed
numbers or other important information. Directory
cards are available as options.
STEP 1: Remove the protective sheet from the cover.
STEP 2: Attach the cover to the directory card andthen attach it to the directory card holder.
ATTACHING HANDSET
 
STEP 1: Insert the coiled cord plug into HANDSETconnector on the...

 30 
INSTALLING/REMOVING KEY SET 
UNIT
 
 
• TO REMOVE KEY SET UNIT
STEP 1: Insert a tapered rod lightly into the right side of the line key panel/button panel.
STEP 2: Lift out the line key panel/button panel to re- move it from the telephone.
STEP 3: Remove the line key card.• TO INSTALL KEY SET UNITSTEP 1: Align the holes in  the line key card with the
buttons on the telephone.
STEP 2: Align the holes in  the line key panel/button
panel with the buttons on the telephone and then push the four corners...

 31 
WALL MOUNTING
 
 
A wall mount unit (WM-L UNIT) is used to mount all
telephones to the wall. This  unit connects to the back
side of the telephone.
To mount the telephone set  on the wall, the following
space is required. To mount the telephone set on the wall, use the
following procedure.
STEP 1: Mount the hanger of the handset upside
down. 
  Remove the hanger from the handset once. Turn it upside down and then insert the hang-
er until you hear it clicks.
STEP 2: Turn the telephone set upside...

 32 
- When attaching WM-L UNIT to the wall plate:
  Attach WM-L UNIT to the posts on the wall plate as shown in the figure below.
The remainder of the procedure varies between DT300
Series and DT700 Series.
- In the case of DT300 Series:  Go to the next step.
- In the case of DT700 Series:  Go  to  Step  8  after  the LAN cable is connected to the telephone.
STEP 4: Attach the modular terminal to the wall as shown in the following figure. If the modular
connector is attached directly on the wall or
the...

 33 
STEP 8: Insert the four tabs on WM-L UNIT in the tab
slots on the back of the telephone.
  Tuck the excess cord into WM-L UNIT.
WallLine Cord
WM-L Line Connector Telephone
Groove
Modular PlugWall
Tabs Tab Slots