NEC Guardian An Open Application Interface Operations Manual

NDA-30008   Revision 2.0Page 21
Guardian Operations Manual Installation Introduction
Field Definitions
Interval Index – The number by which the following time interval is indexed 
in the database and referred to by the group, extension, and authorization code 
databases. This number must lie within the range from 1 to 15.
Begin Day of Week – The day of the week on which the interval begins and the 
group, authorization code, or extension is administratively turned off. The day 
of week can be one of...

Page 22NDA-30008   Revision 2.0
Installation Introduction Guardian Operations Manual
NEAX Command Assignments
This guide assumes that data settings that affect the operation of all OAI software 
on a system-wide basis have already been assigned on the NEAX2400 
Maintenance Administration Terminal (MAT) commands, the NEAX2000 
Customer Administration Terminal (CAT), or the NEAX2000 Maintenance 
Operations Console (MOC).   Such settings include, for instance, system index 
values and assignment of...

NDA-30008   Revision 2.0Page 23
Guardian Operations Manual Installation Introduction
ASDT Command: Assignment of Station Data
Use this command to associate both the tenant and the route restriction class 
assigned above to a specific station and to specify the telephone class of the station.
(a) Use the same tenant number that was configured for the application through 
the APM.
(b) Make sure that the station number and route restriction class entered to this 
command are the same that are entered to the...

Page 24NDA-30008   Revision 2.0
Installation Introduction Guardian Operations Manual
ASYD Command: Assignment of System Data
(a) System Data 1:
Index 43, bit 0 -- For remote access to PBX, is authorization code required 
after ring back tone (RBT)? 0 = Yes, 1 = No.
Index 43, bit 2 -- Will SST be sent after dialing access code? 0 = No, 
1 = Yes
(b) System Data 2
:
Index 3, bit 5 -- 0 = Authorization Code
1 = Forced Account Code
AATC Command: Assignment of Authorization Code Data
This command should be...

NDA-30008   Revision 2.0Page 25
Guardian Operations Manual Installation Introduction
CMD79:  (Assignment of Internet Address)
Assigns the Internet Address of TCP/IP-Ethernet.
1st data 00–03:  Division No. of Internet Address
2nd data 0–255:  Address Data (1–3 digits)
The Internet Address must be assigned to the 1st data 00–03 as follows:
CM08:  (Checking ID Codes Using AP01)
Basic Functions
1st data: 217 Check ID code
2nd data::0: Check through MP
:1: Check through AP01 package when using ACF. (Set...

Page 26NDA-30008   Revision 2.0
Installation Introduction Guardian Operations Manual
CMD7B:  (Number of ID Code Digits When IP down)
ACF
1st data: 00: Number of ID code digits when AP stops during ACF operation
2nd data :1–3: Number of ID code digits when AP stops
:0 (Initial Value):No ACF operation
Initialization
Follow steps 1-3 below to complete initialization.
Step 1: 
Initialization in 
APMEnter the APM Operations Menu and initialize Guardian through the Non-CRT 
Application option, according to...

NDA-30008    Revision 2.0Page 27
Guardian Operations Manual Administration
Chapter 3 Administration
Overview
The Guardian main menu provides tools which you can use to manage and generate 
reports from the record file, assign or alter passwords, and change or view the 
status of groups, authorization codes, and extensions.
Figure 3-1   Main Menu
GUARDIAN
Enter Password:*** NEC  PROPRIETARY ***
 to accept password,  to quit(1)
(2a)
GUARDIAN
*** SYSTEM  ADMINISTRATION ***
 Arrow keys to move cursor,  to...

Page 28NDA-30008   Revision 2.0
Administration Guardian Operations Manual
NotesGuardian menus are password protected.  You can enter Guardian at one of the 
following levels by entering the appropriate password:
Administrator level – Provides access to every menu option. The default 
password (guardadm) can be changed through the Administrator main menu
Operator level – Allows you to view database information or to generate reports. 
You must assign this password through the Administrator main menu....

NDA-30008   Revision 2.0Page 29
Guardian Operations Manual Administration
Notes (Continued)The System Administrator also requires access to the APM Data Entry menu in 
order to maintain the Guardian databases. 
Note:
Changes to the databases (i.e., adding, deleting, or modifying records) can only 
be made through the APM. The changes are processed into the Guardian working 
databases.
Caution:
 
If 80% of disk space has been used on the system, the following message 
appears immediately after you logon:...

Page 30NDA-30008   Revision 2.0
Administration Guardian Operations Manual
Set OAI Application Logical Name
Guardian can serve multiple tenants (e.g., different departments, different 
campuses, etc.). Each tenant is identified by a unique logical name that is 
configured in the APM during installation. When you enter a logical name on this 
screen, all functions performed are implemented with the tenant associated to that 
logical name until the logical name is reset. 
One tenant could serve more than...