NEC Dterm Series 1 Manual

– 25 –
PICK (Call Pickup – Group)
Permits a station user to answer any calls directed to other lines in the user’s preset Call Pickup Group.
CONF (Three-way Calling)
Enables a station user to establish a three-way conference by connecting an additional party to an already existing 
conversation.
VOICE (Voice Call)
Enables the user to make a call to the called party’s built-in speaker. If the called party’s MIC is on, the called party 
can converse on hands-free.
S-SPD (Speed Calling – System)
Allows a...

– 26 –
MIC (Microphone On/Off)
Allows the user to turn the microphone on and off for use with the speakerphone.
PAGE (Button Page)
Allows the user to toggle between pages when two numbers are registered on One-Touch Speed Calling key.
HSET (Headset)
Allows the user to go off- and on-hook when using the headset.
RLS (Release Key)
Allows the user to release the current call when using the headset, without waiting for the party to hang up.
SIG (Manual Signaling)
Permits station users to send a one-second...

– 27 –
VISIT (Survivable Remote MGC)
Allows a station to indicate a status: when a user is in remote office, VISIT will be blinking. After recovering the main 
office, VISIT will return to light.
RMUTE (Ringer Mute)
Allows a station user to mute or recover station ringing.
>>> (Display Function Next Page)
Allows the user to scroll to the next display screen.

– 28 –
Terminal Setup with the Up/Down Key
Note:Not Displayed for D
term
 65/D
term
 Series III and D
term 
75/D
term
 Series E mode.
D
term
 Series III/D
term
 Series E : North America
D
term
 65/D
term
 75 : Australia, Asia, Latin America, Middle East, Russia
To adjust the handset receiver volume
Press the Up/Down key in the off-hook status or during the call.
LCD indication for North America, Latin America, Asia, Middle East and Russia.
LCD indication for Australia.
To adjust the speaker volume
Press...

– 29 –
To adjust LCD contrast
Press the Up/Down key in the on-hook status. 
Note: When the terminal is connected with 16LD ADM, 16 degrees of LCD contrast are available (8 degrees in terminal 
side and 2 degrees in ADM itself). (In Expansion mode only, Link motion)LCD 

– 30 –
Terminal Setup with the Feature KeyMicrophone On/OffLED on Mic key shows the status of the built-in microphone.
To change microphone status
Press Soft Key associated with the MIC Display or press Feature and 1.To adjust initial receiving volumeHandset receiver volume can be changed.
To change the handset receiver volume
Press Feature and 2. The LCD displays the current volume status.
Press Feature and 2 to alternate between Large and Small volume.
4:26 PM    TUE 13  APR 2004 RCV VOL. SMALL4:26 PM...

– 31 –
To select ringer toneThe D
term
 Series i/D
term
 IP has 10 kinds of ringer tones that you can select.
Press Feature and 3. The LCD displays the selected tone number (n=1 ~ 10).
Note 1:Tone number 5~10. Available since Feature Package 8600 (R13) and requires the correct version of Firmware.
Note 2:Tone number 5, 6, 8~10 (Melody 1, 2, 4~6) will sound continuously. 
4:26 PM    TUE 13  APR 2004 RINGER TONE n
Tone No. Frequency (Hz) Modulation (Hz)
1 520/660 16
2 520/660 8
3 1100/1400 16
4 660/760 16...

– 32 –
To adjust transmission/receiving volumeHandset volume can be changed.
Press Feature and 4. The LCD displays the current volume.
Press Feature and 4 again to alternate between Small and Large volume.To activate hands-freeTo set hands-free on:
Press Feature and 5. The LCD displays:
To set hands-free off:
Press Feature and 6. The LCD displays:Call Indicator lamp on/offThe user can choose to turn the call indicator lamp either on or off during ringing.
Press Feature and 7. The LCD displays:
Note:The...

– 33 –
Dynamic Dial Pad on/offThe user can originate a call at first hand without lifting handset or pressing Speaker key.
Press Feature and 8. The LCD displays:
Note:When this feature is ON, the user may initiate a call by immediately dialing the number and the station will go 
hands-free off-hook automatically. Enabling this feature for a D
term
 IP, restricts the terminals ability to enter the 
D
term
 IP User Menu. Please note when the features on the following pages are used in conjunction with...

– 34 –
Login/Logout (IP Enabled D
term
/D
term 
IP Only)
To Login When login mode is activated, following procedure is required.
Enter login code and press Set key.
  (The station number is used as the Login code.)
Enter the password and press OK key.
 If the login code is accepted, display changes to normal idle status.