NEC Dterm Series 1 Manual

– 15 –
Rear ViewDterm
4D IP
Network Specification
Interface        : Ethernet: 10 Base T/100 Base TX , RJ45
Internet Layer: IPv4
Protocol         : Peer to Peer
Media type    : Auto sensing and manual selection supported. 

– 16 –
Dterm
8D IP, 16D IP, 16LD IP, 32D IP
Note:The PC connector on the IP terminal is exclusively for a PC connection, not a second IP terminal.Network Specification
Interface        : Ethernet 10 Base T/100 Base TX , RJ45 * Multiport Switch
Internet Layer: IPv4
Protocol         : Peer to Peer only
Media type    : Auto sensing and manual selection supported.
PC(X) 

– 17 –
Dterm
4D IP
Adjustable
Removable Base
Quick Disconnect 
Button 

– 18 –
Base ViewDterm
8D IP, 16D IP, 16LD IP, 32D IP
Note:Adjustable/Removable base has been Removed
Optional Adapter supported
Power Method Equipment to be used Switch Position
Industry StandardIEEE 802.3 af Power Switch
AC Adapter1

CISCO Discovery Protocol• CISCO Catalyst Power Switch
• CISCO Power Patch Panel2
Type  Description
PS(A)-R UNIT Survivable adapter to provide local Dterm IP survivability.
AD(A)-2R UNIT Local recording capability.
Power over 
Ethernet SwitchExternal AC Adapter
Optional...

– 19 –
Keys and LampsProgrammable KeysThese are examples of D
term®
 features available by pressing the programmable keys. Some features using feature 
access code may be programmed by the user. Others must be programmed by the telephone system administrator.
AICM
Press key to activate “Automatic Intercom”.
DICM
Press key to activate “Dial Intercom”.
DND (Do Not Disturb)
Press key to activate or cancel “Privacy” feature.
FDA
Press key to activate or cancel “Call Forwarding – All Calls” feature.
FDB
Press...

– 20 –
S&R (Save and Repeat)
Press key to store a number or redial a stored number.
SIG
Press key to cause chime at predetermined station.
NAME
Press key to register name for the key to One-Touch Speed Calling key.
(Available from Feature Package 20-100 R18 software or later version.)LampsCall Indicator Lamp
Lamp at top of D
term
 Display flashes when a call terminates to the terminal.
Lamp lights steadily when a message has been left.
LCD
LCD (Liquid Crystal Display) provides D
term
 activity...

– 21 –
Soft Keys
Note:Soft Key function is available for the terminals with LCD.
The Soft Keys on the D
term
 Series i/D
term
 IP provide a set of functions on the LCD that adapts to the changing state 
of the telephone. While default Soft Key settings are provided, desired functions can be assigned to individual sta-
tions as required. The Soft Keys, at the bottom of the LCD, can display the names of available functions, names of 
user-assigned functions and names of functions assigned by a specific...

– 22 –
Default Function Displays for Each StatusDefault Soft Key settings are provided corresponding to particular functions. Different Soft Key settings are dis-
played at the bottom of the LCD depending on the status, as shown below.
Different patterns of Soft Key settings can be registered for individual call states and assigned to individual terminals 
as required.
4:26 PM    TUE 13  APR 2004
MIC >>>DND
DIAL TONE/DIALING IDLE4:26 PM    TUE 13  APR 2004
MIC >>>PICK (1)
Push >>>4:26 PM    TUE 13  APR...

– 23 –
4:26 PM    TUE 13  APR 2004 TRANSFER 2000
MIC >>>CONF BUSY
CONSULTATION HOLD4:26 PM    TUE 13  APR 2004 BUSY 2000
MIC >>>CB (1)
Push >>>4:26 PM    TUE 13  APR 2004 BUSY 2000
S&R >>>CW
(2)4:26 PM    TUE 13  APR 20042000
MIC >>>DND CONNECTION 

– 24 –
Soft Key FeaturesWhen the Soft Key corresponding to a desired function name is operated, the selected function name starts to blink 
on the LCD. The blinking display of available functions takes precedence over the display of functions specified by 
the Soft Key pattern. (Note)
FDB (Call Forwarding – Busy Line)
Permits a call to a busy station to be immediately forwarded to a predesignated station.
FDA (Call Forwarding – All Calls)
Permits all calls destinated for a particular station to be routed...