Namco Wangan Midnight Operators Manual

							Page 41 5-6 Fitting the DVD Rom
•The supplied DVD-ROMs are designed for this game only. Do not use them
with other games. Do not insert any other DVD-ROMs. These may result in
malfunction.
•Always install one DVD-ROM to each Game PCB Assy.
•Note that the tray automatically closes after approximately 10 seconds.
1. Press the EJECT button on the DVD-ROM drive to open the tray.
2. Mount the DVD-ROM on the tray with the label (print) surface upwards.
3. Press the EJECT button on the DVD-ROM drive to close the tray.
EJECT button DVD-ROM drive
Game PCB Assy
Game PCB Assy
Tray DVD-ROM 
						

							Page 42
6. ADJUSTMENTS
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power switch
is located on the rear of the monitor cabinet.
  
Adjustment or maintenance on this machine should be carried out by
qualified personnel only.
  
Einstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.

 

 


Justeringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
  
Los ajustes y el mantenimiento de esta máquina deben ser realizados
sólo por personal cualificado.
  
L’installation, le service, le réglage, ou la maintenance doivent être
effectués uniquement par les personnes qualifiées.
  
Μετατρπές ή επιδιρθώσεις στα µηανήµατα πρέπει να γίννται µν
απ ε*υσιδτηµένα άτµα.
  
Regolazioni e manutenzione su questa macchina devono essere fatti
solo da personale specializzato.
  
Justering eller vedlikehold på denne maskinen skall bare utføres av
kvalifiserte personell.
  
Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd
te worden door bekwaam personeel.
  
Afinações ou manutenção nesta maquina, deverão ser efectuadas
sómente por pessoal qualificado.
	 		 	
	Justeringar och underhåll på denna maskin skall endast utföras av
kvalificerad personal.

 

 


Tätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden
omaava henkilökunta.
l 
						

							Page 43
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door.
1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings. (Refer to section
6-3 Test Mode page 44)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test and to change settings with\
in a
test.
2 Amp Q/B
(Coin Fuse)
COIN COUNTER
TEST
SERVICE TESTSERVICE
ENTER
ENTER
UP
SELECT DOWN
UP
SELECT DOWN 
PLAYER 1
PLAYER 2 
						

							Page 44 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will be
displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of the
selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test to
return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to return
to normal game mode.
The Test Switch must always be in the “OFF” position for normal game mode.
  
 MENU
COIN OPTIONS    Used to set the price of play.
GAME OPTIONS    Used to set the game options.
I/O TEST    Used for testing switches, and lamps.
MONITOR TEST    Used for setting the monitor.
SOUND TEST    Used for setting the volume.
ADS DATA    Used to view bookkeeping.
OTHERS    Used for testing the PCB.
The internal battery’s dead  Only displayed when the battery is fault
y
    (Refer to your Distributor).
SELECT SW : CHOOSE      ENTER SW : ENTER 
						

							Page 45 6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost and
related settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the
Enter button.
3. Use the Select Up/Down switch to change the setting.
4. Press the Enter button to return to option select mode.
5. Select “EXIT” and press the Enter button to return to the menu screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech.
Ensure that the Game Cost is set to 1 Coin 1 Credit.
m e t Ino i t p i r c s e Dte S - e r P
t s o C e m a G ) a (9 ~ 1 e l b a t t e s - - - - - s t i d e r c f o r e b m u n r o f d e r i u q e r s n i o Ct i d e r C 1 n i o C 1
t s o C e u n i t n o C ) b (9 ~ 1 e l b a t t e s - - - - - - e m a g e h t e u n i t n o c o t d e r i u q e r s n i o Cn i o C 1
y a l P e e r F ) c () o N ( f f O / ) s e Y ( n O - - - - - t i d e r c r o f d e r i u q e r s n i o c o NF F O
  
 COIN OPTIONS
 
  [DEFAULT IN GREEN]
GAME COST  1 COIN [S]  1 CREDIT  (a)
CONTINUE COST  1 COIN [S]  1 CREDIT  (b)
FREE PLAY  OFF    (c)
EXIT
SELECT SW : CHOOSE      ENTER SW : ENTER 
						

							Page 46 6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the game variables, the
following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the
Enter button.
3. Use the Select Up/Down switch to change the setting.
4. Press the Enter button to return to option select mode.
5. Select “EXIT” and press the Enter button to return to the menu screen.
  
 GAME OPTIONS
  [DEFAULT IN GREEN]
 LINK OFF
PCB ID  1  (a)
SCENARIO DIFFICULTY  C (MEDIUM)  (b)
VS COUNT  2  (c)
VS PRIORITY  ON  (d)
OFFICIAL RANKING MESSAGE  ON  (e)
RECORD INITIALIZE    (f)
EXIT
SELECT SW : CHOOSE      ENTER SW : ENTER
m e t Ino i t p i r c s e Dte S - e r P
) a (DI B C P) T H G I R ( 2 , ) T F E L ( 1 D I B C P e m a G s t e S
2 r e b m u n s i r e y a l p t h g i r e h t d n a 1 r e b m u n s i r e y a l p t f e l e h T1
) b (yt l u c i f f i D o i r a n e c S) d r a H y r e V - E ~ y s a E y r e V - A ( y t l u c i f f i d e m a g r e y a l p 1 e h t s t e S) m u i d e M ( C
) c (tn u o C S V) 3 , 2 , 1 ( e m a g e d o M n o i t e p m o C n i w o t d e r i u q e r s t n i o p f o r e b m u N2
) d (yt i r o i r P S Ve m a g f o t r a t s t a n o i t p o n I - y u B
d e t c e j e r n i - y u B F F O . d e t p e c c a n I - y u b N ON O
) e (g n i k n a R l a i c i f f O
e g a s s e Mn o i t p o s i h T . d r o w s s a p e h t d n a g n i k n a R t e n r e t n I e h t f o y a l p s i d e h t s t e S
] m u i d e m C [ e u l a v t l u a f e d t a s i ) b ( m e t i n e h w N O t e s e b y l n o n a c
) d e y a l p s i d t o n ( F F O , ) d e y a l p s i d ( N ON O
) f (ez i l a i t i n I d r o c e R. d r o c e R e s r u o C e h t t e s e r o t e c i o h c s w o l l A
) d e z i l a i t i n I ( S E Y ) d e z i l a i t i n i t o n ( O NO N 
						

							Page 47
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to test the switches and lamps. The
following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the\
 Enter button to enter the test.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een.
(a) Shows the condition of the DIP Switches on the PCB. In normal operation \
all switches are ON. (If a switch is ON, it will be displayed in red.)
(b)  Checks function of I/O PCB.  (see Section 6-3-3-1 page 48)
(c)  Initialize game potentiometers.   (see Section 6-3-3-2 page 48)
(d) Selecting this item allows all switches to be checked. (See 6-3-3-3 page 49)
(e) Selecting this item allows the testing of the lamps. (See 6-3-3-4 page 50)
   
 I/O TEST
  DIP SW  1234 [ON RED]  (a)
 LINK OFF
I/O PCB CHECK  (b)
GO TO [I/F] INITIALIZE  (c)
SWITCH TEST  (d)
LAMP TEST  (e)
EXIT
SELECT SW : CHOOSE      ENTER SW : ENTER 
						

							Page 48
6-3-3-1 I/O PCB Test
1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following screen is
displayed:-
Note: This screen is for information only. No adjustments are available.
6-3-3-2 Go to [I/F Initialize]
This item initializes the control devices.
Selecting this option displays the I/F INITIALIZE screen which allows in\
itialization of
the Potentiometer settings for the Steering wheel, Accelerator and Brake Pedals.
(see section 7 page 59)
   
 I/O TEST
  DIP SW  1234 [ON RED]
 LINK OFF
  I/O PCB CHECK
namco ltd.;FCA - 1;ver 1;JPN,
Multipurpose + Rotary Encoder
EXIT
SELECT SW : CHOOSE      ENTER SW : ENTER 
						

							Page 49
6-3-3-3 Switch Test
1. Select “Switch Test” on the I/O menu screen to test the switches.
The following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT and ret\
urn to the I/O menu screen
(a) Increases neach time a credit signal is sent from the CashFlow.
(b to e) Display will change from OFF to ON each time a switch is operated.
(f) Numbers increase when the steering is turned to the right and decrease when turned to the left. Right OK and Left OK is displayed just before the
steering wheel is turned to its full extent. Centre is displayed when the
steering wheel is in the central position.
.
(g) Numbers increase when the accelerator pedal is pressed, and OK is displayed just before the pedal reaches its full travel.
(h) Numbers increase when the brake pedal is pressed, and OK is displayed just before the pedal reaches its full travel.
(i & j) The display will change from OFF to ON each time the switch is operated.\
Note: If Left OK or Right OK is not displayed when the steering is turned or O\
K is not displayed when the pedals are pressed reinitialize the game. (see
section 7 page 59)
   
 I/O TEST
  DIP SW  1234 [ON RED]   
 LINK OFF
 SWITCH TEST
COIN 0  (a)
SERVICE OFF  (b)
TEST ON  (c)
SELECT OFF  (d)
ENTER OFF  (e)
STEERING   +480  RIGHT OK  (f)
GAS  500  OK  (g)
BRAKE  500  OK  (h)
SHIFT UP  (i)
VIEW CHANGE  OFF  (j)
  EXIT : UP SELECT + ENTER SW 
						

							Page 50 6-3-3-4  Lamp Test
1. Select ‘LAMP TEST’ from the I/O Test Screen. The following screen is
displayed:-
(a) The View Change lamp will turn On or OFF each time the Enter
switch is pressed, and the display will change from OFF to ON.
  
 I/O TEST
 
  DIP SW  1234 [ON RED]   
 LINK OFF
 
 LAMP TEST
VIEW CHANGE  OFF  (a)
EXIT
SELECT SW : CHOOSE     ENTER SW : ENTER