Namco Wangan Midnight Operators Manual

Page 61
  
Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te
worden door bekwaam personeel.
Zorg ervoor dat de machine UITgeschakeld is voordat er enig onderhoudswerk
wordt verricht (troubleshooting, reparaties etc.)
  
Afinações ou manutenção nesta maquina, deverão ser efectuadas sómente por
pessoal qualificado.
Certifique-se que a maquina se encontra desligada sempre que iniciar qualquer
tipo de trabalho de manutenção. (identifação de avarias, reparação etc.)...

Page 62
8-1 Error Messages
The machine automatically executes a self-test when the power is turned ON and continues
to monitor operation during Game Play. If the machine is normal, the startup screen appears.
If there is something wrong, the machine beeps or displays an error message on the monitor,
and stops operation.  See below for Error Message details.
t s e T p U - r e w o P g n i r u D s e d o C r o r r E
m o t p m y Ses u a C e l b i s s o Pno i t c Aeg a P e e S
 0 1 R O R R E R O T I N O M 
r e...

Page 63 8-2 Replacing the DVD-Rom Drive
Ensure that the Power to the game is turned OFF before starting work.
1. Remove the Monitor Cabinet Lower Rear Door.
2. Remove the DVD-Rom and place the DVD-Rom in a safe place. (see 5-6
page 41)
3. Disconnect the 7 connectors (shaded) as shown below.
4. Remove The Security Card. Remove 4off pozi head screws (M4x10), with flat
and spring washers, and pull the Front Panel forwards.
Disconnect these connectors
Pozi head screw (with flat/spring washer) (M4 x...

Page 64 5. Disconnect the three connectors as shown shaded in the figure below.
6. Remove 1off pozi head screw (M4x10), with flat and spring washer, and
remove the DVD Drive in the direction of the arrow, as shown below, taking
care not to bend the hook on the rear of the Drive.
7. Remove 4off pozi head screws (M3x6), with flat and spring washers, from the
bottom of the DVD Drive.
8. Reassemble in reverse order.
Note: When shipping the CD Drive, ensure that it is wrapped in sponge or bubble-
wrap and...

Page 65 8-3 Replacing the Steering PCB and/or Fuse
1. Remove 8off button head screws (M5x12) and remove the Monitor Cabinet
Rear Cover.
2. Replace the fuse or:
3. Disconnect the six connectors shown shaded in the diagram below.
4. Loosen 2off pozi head screws (M6), lift the PCB Base to disengage it from the
screws and remove the PCB with the PCB Base.
5. Remove 4off pozi head screws (M3x12), with flat and spring washers, and
remove the Steering PCB.
6. Reassemble in reverse order.
Note: When refitting...

Page 66
8-4 Repacing the Amplifier PCB
1.  Remove the floor plates. (see 5-3 page 38)
2. Disconnect the connectors shown shaded in the diagram below.
3. To remove the Amplifier PCB from the locking supports, squeeze the tabs of the support together and 
gently lift the PCB upwards. Repeat for each
support.
4. Reassemble in reverse order.
PC board
< To reinstall > < To remove >Click!
Locking support
Pliers
Amplifier PC board
Connector 

Page 67 8-5 Replacing the Fluorescent Lamp or Starter.
1. Remove 3off button head screws (M5x12) and remove the top retaining
bracket.
2. Remove the Header Acrylic.
3. Replace the Fluorescent tube or starter.
4. Reassemble in reverse order.
Header Acrylic Top Retaining Bracket
Button head screw (M5 x 12)
StarterFluorescent lamp 

Page 68 8-6 Replacing the Gear Shift Assy
1. Remove 4off security screws (M6x16).
2. Lift the Gear Shift Assembly only sufficient to disconnect the connector.
3. Remove the Gear Shift Assy.
4. Reassemble in reverse order.
Security screw (M6 x 16)
Gear Shift Assy
Connector 

Page 69
8-6-1 Replacing the Gear Shift Microswitch
1. 
remove the Gear Shift Assy. (see 8-6 page 68)
2. Disconnect the Fast-On connectors.
3. Remove 2off pozi head screws and remove the Microswitch.
4. Reassemble in reverse order.
Microswitch Pozi head screw
(M3x16) 

Page 70 8-7 Removing the Play Panel Assy
1. Remove the Gear Shifter Assy.
2. Remove 6off security screw (M5x20) and lift the Play Panel only sufficient to
access the connector.
3. Disconnect the connector and lift the Play Panel Assy away.
4. Reassemble in reverse order.
Control panel Assy
Security screw (M5 x 20)
Security screw (M5 x 20)
ConnectorControl panel Assy