Namco Wangan Midnight Operators Manual

Page 41 5-6 Fitting the DVD Rom
•The supplied DVD-ROMs are designed for this game only. Do not use them
with other games. Do not insert any other DVD-ROMs. These may result in
malfunction.
•Always install one DVD-ROM to each Game PCB Assy.
•Note that the tray automatically closes after approximately 10 seconds.
1. Press the EJECT button on the DVD-ROM drive to open the tray.
2. Mount the DVD-ROM on the tray with the label (print) surface upwards.
3. Press the EJECT button on the DVD-ROM drive to close...

Page 42
6. ADJUSTMENTS
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power switch
is located on the rear of the monitor cabinet.
  
Adjustment or maintenance on this machine should be carried out by
qualified personnel only.
  
Einstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.

 

 


Justeringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
  
Los ajustes y el...

Page 43
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door.
1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings. (Refer to section
6-3 Test Mode page 44)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test and...

Page 44 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will be
displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of the
selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test to
return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to return
to normal game mode.
The Test Switch must always be in the “OFF” position for...

Page 45 6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost and
related settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the
Enter button.
3. Use the Select Up/Down switch to change the setting.
4. Press the Enter button to return to option select mode.
5. Select “EXIT” and press the Enter button to return to the menu screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech....

Page 46 6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the game variables, the
following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the
Enter button.
3. Use the Select Up/Down switch to change the setting.
4. Press the Enter button to return to option select mode.
5. Select “EXIT” and press the Enter button to return to the menu screen.
  
 GAME OPTIONS
  [DEFAULT IN GREEN]
 LINK OFF
PCB ID  1  (a)
SCENARIO DIFFICULTY  C (MEDIUM)...

Page 47
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to test the switches and lamps. The
following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the\
 Enter button to enter the test.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een.
(a) Shows the condition of the DIP Switches on the PCB. In normal operation \
all switches are ON. (If a switch is ON, it will be displayed in red.)
(b)  Checks function of I/O PCB.  (see...

Page 48
6-3-3-1 I/O PCB Test
1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following screen is
displayed:-
Note: This screen is for information only. No adjustments are available.
6-3-3-2 Go to [I/F Initialize]
This item initializes the control devices.
Selecting this option displays the I/F INITIALIZE screen which allows in\
itialization of
the Potentiometer settings for the Steering wheel, Accelerator and Brake Pedals.
(see section 7 page 59)
   
 I/O TEST
  DIP SW  1234 [ON RED]
 LINK OFF...

Page 49
6-3-3-3 Switch Test
1. Select “Switch Test” on the I/O menu screen to test the switches.
The following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT and ret\
urn to the I/O menu screen
(a) Increases neach time a credit signal is sent from the CashFlow.
(b to e) Display will change from OFF to ON each time a switch is operated.
(f) Numbers increase when the steering is turned to the right and...

Page 50 6-3-3-4  Lamp Test
1. Select ‘LAMP TEST’ from the I/O Test Screen. The following screen is
displayed:-
(a) The View Change lamp will turn On or OFF each time the Enter
switch is pressed, and the display will change from OFF to ON.
  
 I/O TEST
 
  DIP SW  1234 [ON RED]   
 LINK OFF
 
 LAMP TEST
VIEW CHANGE  OFF  (a)
EXIT
SELECT SW : CHOOSE     ENTER SW : ENTER