Namco Tokyo Wars Operators Manual

Page 31
7. MAINTENANCE
In order to prevent injury or electric shock to service personnel, ensure that
the MAIN POWER IS OFF before attempting any maintenance.
Before performing any work not described in this manual, be sure to contact
your distributor to receive instructions or answers to questions.
Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß
der Netzstecker gezogen werden.
Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muß
vorher der Händler zu Rate gezogen...

Page 32 7-1 Replacing the Fluorescent Tube, Starter and Lamps
1. Remove the four security screws (M4x16) and remove the glass retaining
bracket.
2. Remove the four security screws (M4X20), from the top, and remove the
header acrylic.
3. Replace the fluorescent tube or starter.
4. The lamps are a screw fitting. Turn anti-clockwise to remove.
5. Reassemble in reverse order.
Warning The fluorescent tube may be hot. Take care when handling the
tube.
Warning Vorsicht bei der Leuchtstoffröhre, da dieses noch...

Page 33
7-2 Replacing the Viewpoint and Credit Available Switches
1. Remove the four security screws (M6x25) and washers from the top of th\
e play panel and hinge the play panel forwards.
2. Remove the lamp/switch assembly by pulling it away from the switch body. Replace the switch or lamp.
Note: When replacing the switch ensure that the wires are replaced to th\
e correct terminals
7-3 Removing the Steering Wheel
1. Carefully remove the round hub cover by gently levering out using a flat\
 blade...

Page 34
7-6 Removing the Pedal Assembly
1. Remove the four security screws (M6x25), flat and spring washers and withdraw the pedal assembly from the front of the machine. (
Take care
not to strain the wires.)
2. Disconnect the connector and remove the assembly.
7-7 Replacing the Pedal Potentiometer 1. Remove the pedal assembl y.  (Refer to section 7-6 , above.)
2. Loosen the grub screw and remove the gear. 
3. Replace the potentiometer.
4. When refitting the potentiometer ensure that the locating lug...

Page 35
8. PARTS
1
2
3
4
5
6
8
911
10
7
m e t Ino i t p i r c s e DoN t r a P
1ro t i n o M o l o P  8 2 x e r a t n a H62 0 0 0 0 4 8
2hc t i w S r e g g i r TB3 1 0 0 0 0 0 6
3yl b m e s s A g n i r e e e t S07 0 0 0 8 8 8
4yl b m e s s A n o t t u B e g n a h C w e i V80 7 0 0 2 0 6
5yl b m e s s A n o t t u B t i L n e h W e l b a l i a v A t i d e r C51 2 0 0 2 0 6
6SH R - l a c e D e d i S57 3 0 0 0 0 4
7to P / W y b m e s s A l a d e P e l g n i S89 0 0 0 8 8 8
8mm 5 7 r o t s a C l e v i w S50 0...

Page 36
1
2
3
54
m e t Ino i t p i r c s e DoN t r a P
1ci l y r c A r e d a e H3 3 2 0 0 0 0 3
2tf 4 e b u T t n e c s e r u l F4 1 0 0 0 5 4 6
3re t r a t S0 0 0 0 0 0 3 6
4tt a w 5 2 / C A v 0 4 2 - p m a L l l a b f l o G 4 1 E4 8 0 0 0 0 4 6
5re d l o H p m a L 4 1 E3 0 0 0 0 8 4 6 

Page 37
m e t Ino i t p i r c s e DoN t r a P
1SH L - k c a l B e t a l P r e k a e p S3 0 6 0 0 3 8 8
2SH R - k c a l B e t a l P r e k a e p S4 0 6 0 0 3 8 8
3tt a w 0 2  ½ 4 - r e k a e p s d u o L6 0 0 0 0 0 2 6
4eu l B k r a D - t a e S6 4 0 0 0 0 6 4
5ra e R t a e S - l a c e D6 7 3 0 0 0 0 4
6re k a h S s s a B - r e k a e p s d u o L6 7 0 0 0 0 2 6
7es a B o c m a N - l a c e D6 3 0 0 0 0 0 4
8to o F e l b a t s u j d A 6 1 M9 7 0 0 0 3 8 8
9mm 5 7 - r o t s a C l e v i w S5 0 0 0 0 0 9 5
2
4
1...

Page 38
9. SCHEMATIC 

Page 39 

Page 40