Namco Time Crisis 2 Single Player Operators Manual

Page 41
5. Seperate the Coin Tower from the Monitor Cabinet  on the right hand
game (viewed from the front).  ( see 5-3 page 37)
6. Remove 6off security screw (M5x16) and remove the rear panel. 
7. Connect together the 1way connectors fitted to the 4way EI header on the\
 right hand game (viewed from the front)..
8. Re-assemble in reverse order.
Note :Only connect the 1way connectors on the right hand game, (viewed
f r om the front). The left hand game should not be connected. 

Page 42
6. ADJUSTMENTS
G GG G
GAdjustment or maintenance on this machine should be carried out by
qualified personnel only.
D DD D
DAufstellung, Service, Einstellung und Wartung dürfen nur von dafür
qualifiziertem Fachpersonal durchgeführt werden.
l ll l
lJusteringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
E EE E
ELos ajustes y el mantenimiento de esta máquina deben ser realizados
sólo por personal cualificado.
F FF F
FL’installation, le service, le réglage, ou la...

Page 43
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play 
meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings.  (Refer to
section 6-3  Test Mode page  44)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test...

Page 44 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
be displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of
the selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
to return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to
return to normal game mode.
The Test Switch must always be in the “OFF” position for...

Page 45 6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost
and related settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then
press the Enter button.
3. Use the Up/Down switch to change the setting.
4. Press the Enter button after the changes have been made to return
to the options.
5. Select “EXIT” and press the Enter button to return to the menu
screen.
Note:- The price of play on this machine is set within the...

Page 46
6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the gamevariables. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter button.
3. Use the Up/Down switch to change the setting. 
4. Press the Enter button after the changes have been made to return to the options.
5. Select “EXIT” and press the Enter button to return to the menu screen.
GAME OPTIONS

PLAYER’S LIFE 4 .................................. (a)...

Page 47
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to switches and lamps. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter button to enter the test.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a) Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
(b) Checks that both game PCBs are communicating. If...

Page 48 6-3-3-1 I/O PCB Check
1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following
screen is displayed:-
I/O TEST
DIP 4
12345678 [ON:RED]
LINKON 2
I/O PCB CHECK
Master TX 3536 NAMCO LTD.
Time Crisis 2 ; Ver1.00 ; JPN
1/0 PCB Connect OK namco ltd.
TSS-I/O;Ver2.02;JPN;GUN-EXTENSION
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER
6-3-3-2 Gun Initialize
1. Select ‘GUN INITIALIZE’ from the I/O Test Screen. The following
screen is displayed:-
2. Use the Up/Down switch to select ‘GUN INITIALIZE (CRT)’,...

Page 49 3. Aim the gun at the screen and pull the trigger. A white spot will
appear. If the spot appears where you aimed, the gun initialization is
O.K. If the spot is not where you aimed, press the Enter button to
initialize the gun. The following screen will be displayed.
4. Aim the gun at the centre of the cross and pull the trigger.
5. Slide the test switch OFF to return to normal game mode.
6. Enter test mode and select ‘GUN INITIALIZE’ from the I/O test
screen and check the gun initialization....

Page 50 6-3-3-3 Switch Test
1. Select “Switch Test” on the I/O menu screen to test the switches.
The following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT and
return to the I/O menu screen
(a) Not Used
(b) The display will change from OFF to ON as each switch is
operated.
(c) The game will return to normal play mode if this switch is
turned off.
(d to h) The display will change from OFF to ON as each...