Namco Time Crisis 2 Single Player Operators Manual

							Page 41
5. Seperate the Coin Tower from the Monitor Cabinet  on the right hand
game (viewed from the front).  ( see 5-3 page 37)
6. Remove 6off security screw (M5x16) and remove the rear panel. 
7. Connect together the 1way connectors fitted to the 4way EI header on the\
 right hand game (viewed from the front)..
8. Re-assemble in reverse order.
Note :Only connect the 1way connectors on the right hand game, (viewed
f r om the front). The left hand game should not be connected. 
						

							Page 42
6. ADJUSTMENTS
G GG G
GAdjustment or maintenance on this machine should be carried out by
qualified personnel only.
D DD D
DAufstellung, Service, Einstellung und Wartung dürfen nur von dafür
qualifiziertem Fachpersonal durchgeführt werden.
l ll l
lJusteringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
E EE E
ELos ajustes y el mantenimiento de esta máquina deben ser realizados
sólo por personal cualificado.
F FF F
FL’installation, le service, le réglage, ou la maintenance doivent être
effectués uniquement par les personnes qualifiées.
K KK K
KÌåôáôñïðÝò Þ åðéäéïñèþóåéò óôá ìç÷áíÞìáôá ðñÝðåé íá ãßíï\
íôáé ìüíï áðü
åîïõóéïäïôçìÝíá Üôïìá.
I II I
IRegolazioni e manutenzione su questa macchina devono essere fatti
solo da personale specializzato.
N NN N
NJustering eller vedlikehold på denne maskinen skall bare utføres av
kvalifiserte personell.
O OO O
OAanpassingen of onderhoud aan deze machine dient alleen
uitgevoerd te worden door bekwaam personeel.
P PP P
PAfinações ou manutenção nesta maquina, deverão ser efectuadas
sómente por pessoal qualificado.
S SS S
SJusteringar och underhåll på denna maskin skall endast utföras av
kvalificerad personal.
l ll l
lTätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden
omaava henkilökunta.
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power
switch is located on the rear of the monitor cabinet. 
						

							Page 43
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play 
meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings.  (Refer to
section 6-3  Test Mode page  44)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test and to change settings with\
in
a test.
COIN COUNTER
TEST SER VICE
SELECTSELECT
TEST SERVICE
UP
SELECT DOWN
UP
SELECT DOWN 2 Amp Q/B 
(Coin Fuse)
PLAYER 1 PLAYER 2 
						

							Page 44 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
be displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of
the selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
to return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to
return to normal game mode.
The Test Switch must always be in the “OFF” position for normal game mode.
MENU
COIN OPTIONS............................Used to set the price of play
GAME OPTIONS............................Used to set the game options
I/O TEST............................Used for testing switches & Gun
MONITOR TEST............................Used for setting the monitor
SOUND TEST............................Used for setting the volume
ADS DATA............................Used to view bookkeeping
OTHERS............................Used for testing the PCB
LINK MALFUNCTION 1 2 3.............. (a)
GAME DIFFICULTY L/R:NOT THE SAME............(b) 
} Do not appear when OK
The internal battery’s dead....................... ( c )
SELECT SW : CHOOSE  ENTER SW : ENTER
(a) Error message related to link play
•A message appears if the link play is defective. The number displayed
represents the type of error
•when 1 or 2 is displayed either the main PCB or memory PCB may be
defective. Contact your distributor.
•If 3 is displayed, the software version on the left game PCB is different
from that on the right game PCB. Contact your distributor.
(b) Error message related to difficulty settings
•A message appears if the difficulty settings of the left and right game
PCBs are different. Enter GAME OPTIONS inthe test mode and set
both PCBs the same.
(c) Low battery display
•A message appears if the Main PCB battery is faulty. Contact your
distributor. 
						

							Page 45 6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost
and related settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then
press the Enter button.
3. Use the Up/Down switch to change the setting.
4. Press the Enter button after the changes have been made to return
to the options.
5. Select “EXIT” and press the Enter button to return to the menu
screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech.
Ensure that the Game Cost is set to 1 Coin 1 Credit.
COIN OPTIONS

GAME COST 1 COIN (S) 1 CREDIT.............. (a)
CONTINUE COST 1 COIN (S) 1 CREDIT.............. (b)
FREE PLAY OFF.............. ( c )
EXIT
SELECT SW : CHOOSE  ENTER SW : ENTER
m e t Ino i t p i r c s e Dte S y r o t c a F
t s o C e m a G ) a (9~ 1 e l b a t t e s - - - - s t i d e r c f o r e b m u n r o f d e r i u q e r s n i o Ct i d e r C 1 n i o C 1
e u n i t n o C ) b (9~ 1 e l b a t t e s - - - - e u n i t n o c o t d e r i u q e r s n i o Ct i d e r C 1 n i o C 1
y a l P e e r F ) c ()o N ( f f O / ) s e Y ( n O - - - - t i d e r c r o f d e r i u q e r s n i o c o NFF O 
						

							Page 46
6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the gamevariables. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter button.
3. Use the Up/Down switch to change the setting. 
4. Press the Enter button after the changes have been made to return to the options.
5. Select “EXIT” and press the Enter button to return to the menu screen.
GAME OPTIONS

PLAYER’S LIFE 4 .................................. (a)
DIFFICULTY C (MEDIUM) .................................. (b)
ATTRACT SOUND ON .................................. ( c )
HI-SCORE INIT NO .................................. (d)
YES
EXIT 
SELECT SW : CHOOSE ENTER SW : ENTER
met
Inoitpircse DteSyrotcaF
efiLsreyalP)a
(9~1elbattes----tratsemagtasevilforebmu N4
ytluciffiD)b( )ysaEyreV(A
)ysaE(B )muideM(C
)draH(D )draHyreV(E )muideM(C
dnuoStcarttA)c
(FFO/NOedomtcarttanidnuo SNO
tinIerocs-iH)d
(ON/SEYpu-rewoptadezilaitinierocs-i HON
NOTE:The game will not function correctly unless the di fficulty setting
is the 
same for both players. 
						

							Page 47
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to switches and lamps. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter button to enter the test.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a) Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
(b) Checks that both game PCBs are communicating. If the communication is good LINK ON 2 will be displayed 
If link data is wrong LINK OFF will be displayed.
If unrecognisable data is being received LINK NG will be displayed.
(c) Checks function of I/O PCB. 
(d ) Used to test and initialize the gun operation  
(see Section 6-3-3-2 page 48)
(e) Selecting this item allows all switches and pedal sensor to be checked.
(See 6-3-3-3 page  50)
(f) Selecting this item allows the testing of the gun recoil solenoid. (See 6-3-3-4 page  51)
I/O TEST
DIP 4
12345678 [ON:OFF].............................................. (a)
LINK
ON 2............................................ (b)
I/O PCB CHECK ............................................ ( c )
GUN INITIALIZE ............................................ (d)
SWITCH TEST ............................................ (e)
SOLENOID TEST ............................................ ( f )
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER 
						

							Page 48 6-3-3-1 I/O PCB Check
1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following
screen is displayed:-
I/O TEST
DIP 4
12345678 [ON:RED]
LINKON 2
I/O PCB CHECK
Master TX 3536 NAMCO LTD.
Time Crisis 2 ; Ver1.00 ; JPN
1/0 PCB Connect OK namco ltd.
TSS-I/O;Ver2.02;JPN;GUN-EXTENSION
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER
6-3-3-2 Gun Initialize
1. Select ‘GUN INITIALIZE’ from the I/O Test Screen. The following
screen is displayed:-
2. Use the Up/Down switch to select ‘GUN INITIALIZE (CRT)’, and
press the Enter switch. The following screen is displayed.GUN INITIALIZE
GUN INITIALIZE (CRT)...................... (a)
GUN INITIALIZE (PROJECTOR)...................... (b)
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER 
						

							Page 49 3. Aim the gun at the screen and pull the trigger. A white spot will
appear. If the spot appears where you aimed, the gun initialization is
O.K. If the spot is not where you aimed, press the Enter button to
initialize the gun. The following screen will be displayed.
4. Aim the gun at the centre of the cross and pull the trigger.
5. Slide the test switch OFF to return to normal game mode.
6. Enter test mode and select ‘GUN INITIALIZE’ from the I/O test
screen and check the gun initialization. Repeat initialization if
necessaryGUN INITIALIZE (CRT)
SHOOT AT SCREEN
TO CHECK GUN ACCURACY
PUSH ENTER SW : ADJUST GUN SIGHT
UP SELECT SW + ENTER SW : EXIT
AIM AT CENTER OF THE CROSS
AND PULL GUN TRIGGER 
						

							Page 50 6-3-3-3 Switch Test
1. Select “Switch Test” on the I/O menu screen to test the switches.
The following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT and
return to the I/O menu screen
(a) Not Used
(b) The display will change from OFF to ON as each switch is
operated.
(c) The game will return to normal play mode if this switch is
turned off.
(d to h) The display will change from OFF to ON as each switch is
operated.
SWITCH TEST
DIP 4
123456787 [ON/OFF]
LINK ON 2
SWITCH TEST
COIN
000................................. (a)
SERVICE
OFF................................. (b)
TEST
ON................................. ( c )
UP SELECT
OFF................................. (d)
DOWN SELECT
OFF................................. (e)
ENTER
OFF................................. ( f )
TRIGGER
OFF................................. (g)
FOOT PEDAL
OFF................................. (h)
UP SELECT SW + ENTER SW : EXIT