Namco Time Crisis 2 Single Player Operators Manual

Page 51 6-3-3-4 Solenid Test
1. Select “solenoid Test” on the I/O menu screen to test the switches.
The following screen is displayed.
2. The gun recoil solenoid will operate each time the trigger is pressed.
3. Select ‘EXIT’ and press the Enter button to return to the I/O menu
screen.I/O TEST
DIP 4
12345678 [ON:RED]
LINKON 2
SOLENOID TEST
PULL GUN TRIGGER TO ACTION
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER 

Page 52 6-3-4 Monitor Test
1. Select “MONITOR TEST” on the menu screen to test and adjust the
Monitor. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button. To return to the Monitor Test Menu from a test pattern
press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu screen.
MONITOR TEST
GRADATION PATTERN..................................... (a)
CROSSHATCH PATTERN...

Page 53 6-3-5 Sound Test
1. Select “I/O TEST” on the menu screen to switches and lamps. The
following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button.
3. Use the Up/Down switch to change the setting.
4. Press the Enter button after the changes have been made to return to the
options.
5. Select “EXIT” and press the Enter button to return to the menu screen.
(a) Volume setting for left channel speaker. Settable from 0 ~ 64 with 0
quietest and 64...

Page 54
6-3-6 ADS Data
By selecting ADS Data from the menu screen, all of the bookkeeping 
details can be read and/or reset.
6-3-7 Others 1. Select “OTHERS” on the menu screen. The following screen is displa\
yed. 
2. Use the Select Up/Down switch choose the required item then press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a,) Displays game software version. 
(b) Allows the internal clock and calendar to be set.
(c) Used to test the PCB. (this...

Page 55
7. REMOVING AND REPLACING ASSEMBLIES AND PARTS
7-1 Replacing the MonitorThe monitor is heav y. At least two people are required to remove the monito r.
1. Remove the 2off upper security screw (M5x12) and slacken the 2off lower security screw (M5x12), and remove the monitor rear access panel.
2. Remove the pozi head screw (M4x10) and remove the Earth wire and connectors from the monitor.
3. Remove 8off security screw (M5x16) and remove the monitor vac-form. 

Page 56 4. Remove 4off pozi head screws (M6x25), with flat washer (1”x¼”), and
remove the monitor by tilting the forward and lifting it out.
Note: Take care not to knock the neck of the monitor tube when handling the
monitor as it can be easily damged and the tube destroyed. 

Page 57 7-2 Replacing the Fluorescent Tube or Starter
1. Remove 2off security screw (M5x12) and remove the top retaining bracket
and header acrylic.
2. Replace the fluorescent tube or starter.
3. Refit the header acrylic and top retaining bracket. 

Page 58 7-3 Replacing the Pedal Switch
1. Remove 4off security screw (M5x12) and remove the switch cover plate.
2. Remove 2off pozi head screw (M3x16) and remove the switch.
When replacing the switch, ensure that the wires are fitted to the correct
terminals.
3. Slacken the 2off whizztite nuts (M4) and adjust the microswitch bracket so
that the switch plunger operates the switch correctly without bending the
switch lever against the switch body.
4. Refit the switch cover plate and 4off security screw...

Page 59 7-4 Greasing the Pedal Assy Plunger
1. Remove 4off security screw (M5x12) and remove the switch cover plate.
2. Remove 2off whizztite nuts (M4) and remove the switch.
3. Remove 4off whizztite nuts (M4) and remove the plaunger assembly.
Note: The plunger is spring loaded. Keep the plunger pressed in when
removing the assy and release the plunger slowly.
4. Remove any old grease and dirt from the plunger and pedal plate.
5. Grease both the plate and spherical portion of the plunger.
6. Reassemble...

Page 60
7-5 Replacing the Pedal Plunger
1. Remove the plunger assembl y.  (See 7-4 page  59 )
2. Pull the plunger out of the holder. Replace with the new plunger. (The new plunger should have grease applied all over prior to fitting).
3.  Wipe off any old grease and dirt from the pedal plate and regrease. 
4. Reassemble in reverse order.