Namco Time Crisis 2 Single Player Operators Manual

Page 31
3. MAJOR COMPONENTS 

Page 48
4. MOVING THE MACHINE
WARNING • NEVER turn the power to the machine ON until 
installation has been completed.
WARNING • In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a
securely connected earthed plug.
WARNING • So that customers are not injured , ensure that there is at least 500mm separation between other machines or
walls.
CAUTION • In  order to avoid damage to the machine due to mis-
operation, ensure that the voltage of the mains supply...

Page 33
G
DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an
Plätzen mit Wasseranschlüssen und möglichen Leckagen, nahe Klima- und
Heizungsanlagen, an Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger...

Page 34
F
K
I
N
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er
vannlekasje, nære luft kjølere eller varme elementer, plasser med overdreven
høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.CETTE MACHINE EST DESTINEE...

Page 35
P
l S
 DEZE MACHINE IS ALLEEN VOOR GEBRUIK BINNENSHUIS ONTWORPEN
 INSTALLEER DE MACHINE NIET OP DE VOLGENDE PLAATSEN
1. Buiten
2. In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel
stof, op plaatsen waar een waterlek is, dichtbij airco’s of
verwarmingsapparatuur, op plaatsen met een zeer hoge of koude temperatuur.
3. Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd.
4. Op onstabiele plaatsen of plaatsen waar grote trillingen voorkomen.
5. Op...

Page 36
5-1 Fitting the Header Assembly
The Header Assembly has a forward centre of gravit y, so it is important that at
least  
two peopl e are used to fit or remove the Header Assembl y.
The fitting position of the Header Assembly is very high, and it is impo\
rtant 
that a means of reaching the height safely, without stretching, is available.
(e.g. steps, step stool etc.) 
1. Place the header on to the monitor cabinet and slide it forwards so that\
 it engages under the fixing brackets at the front....

Page 37
5-2 Adjusting the Level Adjusters
1. When the monitor cabinet is in its final position, lower the four (4) level
adjusters with a spanner so that the machine is level and all castors are
raised from the floor by approx. 5mm. Tighten the lock nuts with a
spanner to ensure that the level adjusters do not move.
Note: If the location site of this machine has a polished floor it is
recommended that rubber pads are fitted under the level adjusters to
prevent the machine sliding on the floor when in...

Page 38
3. Retain the coin tower to the joint box with 4off hex head screws (M8x20),
flat and spring washers.
4. Connect the connector and refit the joint box cover plate with 4 off security screw (M5x12).
5.  Adjust the level adjusters on the coin tower so that the coin tower is stable and level with the monitor cabinet. ( see section 5-2 page 37) 

Page 39 5-4 Fitting the Pedal Assembly
1. Fit, finger tight only, the joint brackets to the coin tower, with
4off security button head screw (M5x12).
2. Place the pedal assembly close to the coin tower and connect the
connector.
3. Fit the pedal assembly inside the joint brackets, taking care not to trap
any wires and fit, finger tight, the 4off security button head screws
(M5x12).
4. Ensure that the pedal assembly is flat on the ground and tighten fully the
4off security button head screws (M5x12) and...

Page 40 5-5 Linking two Machines
1. Switch both machines off.
2. Remove 2off pozi head screws (M5x12) and remove the Link Cover
Bracket.
3. Fit the Link Cables (supplied) as shown in the following diagram.
4. Refit the Link Cover Bracket with the 2off pozi head screws (M5x12).