Namco Time Crisis 2 Deluxe Operators Manual

							Page 41 5-4 Fitting the Pedal Assembly
1. Connect the connector between the pedal assy and coin tower assy.
2. Slacken the Flange socket head screws (M6x20) retaining the pedal
brackets.
3. Place the pedal assy between the pedal brackets and fit, finger tight,  the
supplied 4off flange socket head screws (M5x12) taking care not to trap
any wires.
4. Ensure that the pedal assy is against the floor and tighten the 4off flange
socket head screws (M5x12)
Note: Make sure that the pedal assy does not lift from the floor.
5. Re-tighten the flange socket head screws (M6x20). 
						

							Page 42
6. ADJUSTMENTS
G GG G
GAdjustment or maintenance on this machine should be carried out by
qualified personnel only.
D DD D
DAufstellung, Service, Einstellung und Wartung dürfen nur von dafür
qualifiziertem Fachpersonal durchgeführt werden.
l ll l
lJusteringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
E EE E
ELos ajustes y el mantenimiento de esta máquina deben ser realizados
sólo por personal cualificado.
F FF F
FL’installation, le service, le réglage, ou la maintenance doivent être
effectués uniquement par les personnes qualifiées.
K KK K
KÌåôáôñïðÝò Þ åðéäéïñèþóåéò óôá ìç÷áíÞìáôá ðñÝðåé íá ãßíï\
íôáé ìüíï áðü
åîïõóéïäïôçìÝíá Üôïìá.
I II I
IRegolazioni e manutenzione su questa macchina devono essere fatti
solo da personale specializzato.
N NN N
NJustering eller vedlikehold på denne maskinen skall bare utføres av
kvalifiserte personell.
O OO O
OAanpassingen of onderhoud aan deze machine dient alleen
uitgevoerd te worden door bekwaam personeel.
P PP P
PAfinações ou manutenção nesta maquina, deverão ser efectuadas
sómente por pessoal qualificado.
S SS S
SJusteringar och underhåll på denna maskin skall endast utföras av
kvalificerad personal.
l ll l
lTätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden
omaava henkilökunta.
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power
switch is located on the rear of the monitor cabinet. 
						

							Page 43
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play 
meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings.  (Refer to
section 6-3 Test Mode page  44)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test and to change settings with\
in
a test.
COIN COUNTER
TEST SERVICE
SELECTSELECT
TESTSERVICE
UP
SELECT DOWN
UP
SELECT DOWN 2 Amp Q/B 
(Coin Fuse)
PLAYER 1 PLAYER 2 
						

							Page 44 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
be displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of
the selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
to return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to
return to normal game mode.
The Test Switch must always be in the “OFF” position for normal game mode.
MENU
COIN OPTIONS............................Used to set the price of play
GAME OPTIONS............................Used to set the game options
I/O TEST............................Used for testing switches & Gun
MONITOR TEST............................Used for setting the monitor
SOUND TEST............................Used for setting the volume
ADS DATA............................Used to view bookkeeping
OTHERS............................Used for testing the PCB
LINK MALFUNCTION 1 2 3.............. (a)
GAME DIFFICULTY L/R:NOT THE SAME............(b) 
} Do not appear when OK
The internal battery’s dead...................... ( c )
SELECT SW : CHOOSE  ENTER SW : ENTER
(a) Error message related to link play
•A message appears if the link play is defective. The number displayed
represents the type of error
•when 1 or 2 is displayed either the main PCB or memory PCB may be
defective. Contact your distributor.
•If 3 is displayed, the software version on the left game PCB is different
from that on the right game PCB. Contact your distributor.
(b) Error message related to difficulty settings
•A message appears if the difficulty settings of the left and right game
PCBs are different. Enter GAME OPTIONS inthe test mode and set
both PCBs the same.
(c) Low battery display
•A message appears if the Main PCB battery is faulty. Contact your
distributor. 
						

							Page 45 6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost
and related settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then
press the Enter button.
3. Use the Up/Down switch to change the setting.
4. Press the Enter button after the changes have been made to return
to the options.
5. Select “EXIT” and press the Enter button to return to the menu
screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech.
Ensure that the Game Cost is set to 1 Coin 1 Credit.
COIN OPTIONS

GAME COST 1 COIN (S) 1 CREDIT.............. (a)
CONTINUE COST 1 COIN (S) 1 CREDIT.............. (b)
FREE PLAY OFF.............. ( c )
EXIT
SELECT SW : CHOOSE  ENTER SW : ENTER
M E T INO I T P I R C S E DTE S Y R O T C A F
t s o C e m a G ) a (9- 1 e l b a t t e s - - - - - s t i d e r C f o r e b m u n r o f d e r i u q e r s n i o Ct i d e r C 1 n i o C 1
e u n i t n o C ) b (9- 1 e l b a t t e s - - - - - e u n i t n o c o t d e r i u q e r s n i o Ct i d e r C 1 n i o C 1
y a l P e e r F ) c ()o N ( f f O / ) s e Y ( n O - - - - - t i d e r c r o f d e r i u q e r s n i o c o NFF O 
						

							Page 46
6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the gamevariables. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter button.
3. Use the Up/Down switch to change the setting. 
4. Press the Enter button after the changes have been made to return to the options.
5. Select “EXIT” and press the Enter button to return to the menu screen.
GAME OPTIONS

PLAYER’S LIFE 4 .................................. (a)
DIFFICULTY C (MEDIUM) .................................. (b)
ATTRACT SOUND ON .................................. ( c )
HI-SCORE INIT NO .................................. (d)
YES
EXIT 
SELECT SW : CHOOSE ENTER SW : ENTER
MET
INOITPIRCSE DTESYROTCAF
efiLsreyalP)a
(9-1elbattes----tratsemagtasevilforebmu N4
ytluciffiD)b( )ysaEyreV(A
)ysaE(B )muideM(C
)draH(D )draHyreV(E )muideM(C
dnuoStcarttA)c
(FFO/NOedomtcarttanidnuo SNO
?tinIerocS-iH)d
(ON/SEYpurewoptadezilaitinierocS-i HON
NOTE:The game will not function correctly unless the difficulty setting
is the 
same for both players. 
						

							Page 47
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to switches and lamps. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter button to enter the test.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a) Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)\
(b) Checks that both game PCBs are communicating. If the communication is good LINK ON 2 will be displayed 
If link data is wrong LINK OFF will be displayed.
If unrecognisable data is being received LINK NG will be displayed.
(c) Checks function of I/O PCB. 
(d ) Used to test and initialize the gun operation  
(see Section 6-3-3-2 page 49)
(e) Selecting this item allows all switches and pedal sensor to be checked.
(See 6-3-3-3 page  52)
(f) Selecting this item allows the testing of the gun recoil solenoid. (See 6-3-3-4 page  53)
I/O TEST
DIP 4
12345678 [ON:OFF].............................................. (a)
LINK
ON 2............................................ (b)
I/O PCB CHECK ............................................ ( c )
GUN INITIALIZE ............................................ (d)
SWITCH TEST ............................................ (e)
SOLENOID TEST ............................................ ( f )
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER 
						

							Page 48 6-3-3-1 I/O PCB Check
1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following
screen is displayed:-
I/O TEST
DIP 4
12345678 [ON:RED]
LINKON 2
I/O PCB CHECK
Master TX 3536 NAMCO LTD.
Time Crisis 2 ; Ver1.00 ; JPN
1/0 PCB Connect OK namco ltd.
TSS-I/O;Ver2.02;JPN;GUN-EXTENSION
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER 
						

							Page 49 6-3-3-2 Gun Initialize
1. Select ‘GUN INITIALIZE’ from the I/O Test Screen. The following
screen is displayed:-
2. Use the Up/Down switch to select ‘GUN INITIALIZE (PROJECTOR)’,
and press the Enter switch. The following screen is displayed.
3. This screen allows the gun accuracy to be checked. Shoot the gun at
the screen. The screen will display the position of the bullet. If the
position is not where the gun was aimed press the ‘Enter sw’ or press
on the pedal. The following screen will be dispalyed.GUN INITIALIZE
GUN INITIALIZE (CRT)...................... (a)
GUN INITIALIZE (PROJECTOR)...................... (b)
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER
GUN INITIALIZE (PROJECTOR)
SHOOT AT SCREEN
TO CHECK GUN ACCURACY
PUSH ENTER SW : ADJUST GUN SIGHT
UP SELECT SW + ENTER SW : EXIT 
						

							Page 50 AIM AT CENTER OF THE CROSS
AND PULL GUN TRIGGER
4. The gun aim is set by aiming and shooting at three points on the
screen: the middle, top and bottom.
5. While the above screen is displayed, aim at the centre of the cross
displayed in the middle of the screen. After firing the gun the
following screen is displayed.
6. While the above screen is displayed, aim at the centre of the cross
displayed at the top of the screen. After firing the gun the following
screen is displayed.AIM AT CENTER OF THE CROSS
AND PULL GUN TRIGGER