Namco Time Crisis 2 Deluxe Operators Manual

Page 41 5-4 Fitting the Pedal Assembly
1. Connect the connector between the pedal assy and coin tower assy.
2. Slacken the Flange socket head screws (M6x20) retaining the pedal
brackets.
3. Place the pedal assy between the pedal brackets and fit, finger tight,  the
supplied 4off flange socket head screws (M5x12) taking care not to trap
any wires.
4. Ensure that the pedal assy is against the floor and tighten the 4off flange
socket head screws (M5x12)
Note: Make sure that the pedal assy does not lift from...

Page 42
6. ADJUSTMENTS
G GG G
GAdjustment or maintenance on this machine should be carried out by
qualified personnel only.
D DD D
DAufstellung, Service, Einstellung und Wartung dürfen nur von dafür
qualifiziertem Fachpersonal durchgeführt werden.
l ll l
lJusteringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
E EE E
ELos ajustes y el mantenimiento de esta máquina deben ser realizados
sólo por personal cualificado.
F FF F
FL’installation, le service, le réglage, ou la...

Page 43
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play 
meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings.  (Refer to
section 6-3 Test Mode page  44)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test...

Page 44 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
be displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of
the selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
to return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to
return to normal game mode.
The Test Switch must always be in the “OFF” position for...

Page 45 6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost
and related settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then
press the Enter button.
3. Use the Up/Down switch to change the setting.
4. Press the Enter button after the changes have been made to return
to the options.
5. Select “EXIT” and press the Enter button to return to the menu
screen.
Note:- The price of play on this machine is set within the...

Page 46
6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the gamevariables. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter button.
3. Use the Up/Down switch to change the setting. 
4. Press the Enter button after the changes have been made to return to the options.
5. Select “EXIT” and press the Enter button to return to the menu screen.
GAME OPTIONS

PLAYER’S LIFE 4 .................................. (a)...

Page 47
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to switches and lamps. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter button to enter the test.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a) Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)\
(b) Checks that both game PCBs are communicating. If...

Page 48 6-3-3-1 I/O PCB Check
1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following
screen is displayed:-
I/O TEST
DIP 4
12345678 [ON:RED]
LINKON 2
I/O PCB CHECK
Master TX 3536 NAMCO LTD.
Time Crisis 2 ; Ver1.00 ; JPN
1/0 PCB Connect OK namco ltd.
TSS-I/O;Ver2.02;JPN;GUN-EXTENSION
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER 

Page 49 6-3-3-2 Gun Initialize
1. Select ‘GUN INITIALIZE’ from the I/O Test Screen. The following
screen is displayed:-
2. Use the Up/Down switch to select ‘GUN INITIALIZE (PROJECTOR)’,
and press the Enter switch. The following screen is displayed.
3. This screen allows the gun accuracy to be checked. Shoot the gun at
the screen. The screen will display the position of the bullet. If the
position is not where the gun was aimed press the ‘Enter sw’ or press
on the pedal. The following screen will be...

Page 50 AIM AT CENTER OF THE CROSS
AND PULL GUN TRIGGER
4. The gun aim is set by aiming and shooting at three points on the
screen: the middle, top and bottom.
5. While the above screen is displayed, aim at the centre of the cross
displayed in the middle of the screen. After firing the gun the
following screen is displayed.
6. While the above screen is displayed, aim at the centre of the cross
displayed at the top of the screen. After firing the gun the following
screen is displayed.AIM AT CENTER OF THE...