Namco Time Crisis 2 Deluxe Operators Manual

Page 31
3. MAJOR COMPONENTS 

Page 32
4. MOVING THE MACHINE
WARNING •NEVER turn the power to the machine ON until 
installation has been completed.
WARNING • In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a
securely connected earthed plug.
WARNING • So that customers are not injured , ensure that there is at least 500mm separation between other machines or
walls.
CAUTION • In  order to avoid damage to the machine due to mis-
operation, ensure that the voltage of the mains supply...

Page 33
G
DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an
Plätzen mit Wasseranschlüssen und möglichen Leckagen, nahe Klima- und
Heizungsanlagen, an Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger...

Page 34
F
K
I
N
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er
vannlekasje, nære luft kjølere eller varme elementer, plasser med overdreven
høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.CETTE MACHINE EST DESTINEE...

Page 35
P
l S
 DEZE MACHINE IS ALLEEN VOOR GEBRUIK BINNENSHUIS ONTWORPEN
 INSTALLEER DE MACHINE NIET OP DE VOLGENDE PLAATSEN
1. Buiten
2. In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel
stof, op plaatsen waar een waterlek is, dichtbij airco’s of
verwarmingsapparatuur, op plaatsen met een zeer hoge of koude temperatuur.
3. Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd.
4. Op onstabiele plaatsen of plaatsen waar grote trillingen voorkomen.
5. Op...

Page 36
5-1 Joining the Monitor (L) and (R) Assemblies
1. Place the monitor (L) and (R) assemblies together in their final location
and lower the eight, (4 on each monitor), level adjusters until the castors
are raised approx 5mm from the ground.
NOTE:- When adjusting the level adjusters, ensure that the top and front faces of
the monitor assemblies are level with each other.
Poor adjustment will prevent the fitting of the Joint Assy and Header Assy.
Note: If the location site of this machine has a...

Page 37
2. Fit the joint bracket with the supplied 4off flange socket head screws
(M8x20)
3. Fit the supplied 4off flange socket head screws (M8x40) to the front of
both monitor (L) and (R) assemblies finger tight, leaving a clearance of
approx. 5mm. 

Page 38 4. Fit the joint assy, (shipped with Header Assy), to the monitors and tighten
the 4off flange socket head screws (M8x40).
5. Pull the loom connectors from the monitor assemblies. 

Page 39
5-2 Fitting the Header Assembly
The Header Assembly has a forward centre of gravity, so it is important \
that at 
least 
two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is very high, and it is impo\
rtant 
that a means of reaching the height safely, without stretching, is avail\
able.
(e.g. steps, step stool etc.) 
1. Remove 2off tork screws (M5x15) and remove the connector cover. 
2. Place the header on to the monitor cabinets and slide it...

Page 40 5-3 Fitting the Coin Tower
1. Place the coin tower up to the Joint Assy.
2. Fit the supplied 4off flange socket head screws (M8x20)  to fix the Coin
tower to the Joint Assy.
3. Pull the harness out from the coin tower.
4. Connect the six connectors.
5. Fit the joint cover using 4off tork screws (M5x12).