Namco Time Crisis 2 Deluxe Operators Manual

Page 51 7. While the above screen is displayed, aim at the centre of the cross
displayed at the bottom of the screen. After firing the gun aiming is
now set, and the screen will return to the original ‘Gun Initialize’
screen.
8. Aim and fire the gun at the screen to check the new gun aiming. If
the aiming is correct press the Up Select sw and Enter switch
together to return to the ‘I/O Test’ screen. If the gun aiming is
incorrect repeat steps 3 to 8.AIM AT CENTER OF THE CROSS
AND PULL GUN TRIGGER 

Page 52 6-3-3-3 Switch Test
1. Select “Switch Test” on the I/O menu screen to test the switches.
The following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT and
return to the I/O menu screen
(a) Not Used
(b) The display will change from OFF to ON as each switch is
operated.
(c) The game will return to normal play mode if this switch is
turned off.
(d to h) The display will change from OFF to ON as each...

Page 53 6-3-3-4 Solenid Test
1. Select “solenoid Test” on the I/O menu screen to test the switches.
The following screen is displayed.
2. The gun recoil solenoid will operate each time the trigger is pressed.
3. Select ‘EXIT’ and press the Enter button to return to the I/O menu
screen.I/O TEST
DIP 4
12345678 [ON:RED]
LINKON 2
SOLENOID TEST
PULL GUN TRIGGER TO ACTION
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER 

Page 54 6-3-4 Monitor Test
1. Select “MONITOR TEST” on the menu screen to test and adjust the
Monitor. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button. To return to the Monitor Test Menu from a test pattern
press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu screen.
MONITOR TEST
GRADATION PATTERN..................................... (a)
CROSSHATCH PATTERN...

Page 55 6-3-5 Sound Test
1. Select “I/O TEST” on the menu screen to switches and lamps. The
following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button.
3. Use the Up/Down switch to change the setting.
4. Press the Enter button after the changes have been made to return to the
options.
5. Select “EXIT” and press the Enter button to return to the menu screen.
(a) Volume setting for left channel speaker. Settable from 0 ~ 64 with 0
quietest and 64...

Page 56
6-3-6 ADS Data
By selecting ADS Data from the menu screen, all of the bookkeeping 
details can be read and/or reset.
6-3-7 Others 1. Select “OTHERS” on the menu screen. The following screen is displa\
yed. 
2. Use the Select Up/Down switch choose the required item then press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a,) Displays game software version. 
(b) Allows the internal clock and calendar to be set.
(c) Used to test the PCB. (this...

Page 57
7. REMOVING AND REPLACING ASSEMBLIES AND PARTS
7-1 Removing the Monitor from the Monitor Base
The monitor is heavy. approx 100kg
At least five (5) people are required to remove the monitor.
1. Remove the 4off pozi head screws (M5x35) and remove the front cover. 
2. Disconnect the two connectors and then remove the 2off hex head screws (M10x130), spring washers and square flat washers 

Page 58 3. Remove the 2off pozi head screws (M5x30) and remove the cover strip.
4. Remove 2off pozi head screws (M5x30), unlock and remove the rear door.
5. Remove the 2off hex head screws (M10x130), spring washers and square
flat washers.
6. Lift the Monitor approx 10cm from the monitor base and then move it
forwards or backwards clear of the monitor base.
Note: When placing the monitor on to the floor or replacing on to the monitor
base, take care not to trap hands or fingers. 

Page 59 7-2 Replacing the Fluorescent Tube or Starter
1. Remove 4off tork screw (M5x15) and remove the top retaining bracket
and header acrylic.
2. Replace the fluorescent tube or starter.
3. Refit the header acrylic and top retaining bracket. 

Page 60 7-3 Replacing the Pedal Switch
1. Remove 4off security screw (M5x12) and remove the switch cover plate.
2. Remove 2off pozi head screw (M3x16) and remove the switch.
When replacing the switch, ensure that the wires are fitted to the correct
terminals.
3. Slacken the 2off whizztite nuts (M4) and adjust the microswitch bracket so
that the switch plunger operates the switch correctly without bending the
switch lever against the switch body.
4. Refit the switch cover plate and 4off security screw...