Namco Rapid River Operators Manual

							Page 42
3. Remove 8off Hex head screws (M10x20), and remove the four shipping
brackets.
4.  Refit the 8off Hex head screws previously removed.
5. Remove the four nuts (M8).
6. Place one shipping bracket (removed in step 3) on top of another and
retain each pair, for future use, on the studs with the four nuts (M8)
removed in step 5. 
						

							Page 43 7. Connect the connectors and air tube.
8. Replace the joint cover removed in step 1.
Note: The air tube is a push fit. Ensure that the tube is pushed fully in when
fitting.
When removing the air tube push the blue ring of the connector in and
whilst holding it in, pull the air tube out.
If the compressor reservoir tank has air in it, a loud noise will be heard
as the air escapes when the air tube is removed.
9. When the machine is in its final position, lower the eight level adjusters,
(4 on the monitor cabinet and 4 on the ride assy), with a spanner so that
the machine is level and all castors are raised from the floor by approx.
5mm. Tighten the lock nuts with a spanner to ensure that the level
adjusters do not move.
Note: If the location site of this machine has a polished floor it is recommended
that rubber pads are fitted under the level adjusters to prevent the
machine sliding on the floor when in use. 
						

							Page 44 5-4 Fitting the Paddles
1. Fit the blade assy into the paddle assy.
2. Adjust the angle of the blade so that the spring pin of the blade assy is
aligned with the screw hole of the paddle assy. Tighten the nut to fix the
blade assy.
3. Fit the grub screw (M6x10) into the screw hole of the paddle assy. 
						

							Page 45
6. ADJUSTMENTS
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power
switch is located on the rear of the monitor cabinet.
G GG G
GAdjustment or maintenance on this machine should be carried out by
qualified personnel only.
D DD D
DEinstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.
l ll l
lJusteringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
E EE E
ELos ajustes y el mantenimiento de esta máquina deben ser realizados
sólo por personal cualificado.
F FF F
FL’installation, le service, le réglage, ou la maintenance doivent être
effectués uniquement par les personnes qualifiées.
K KK K
KÌåôáôñïðÝò Þ åðéäéïñèþóåéò óôá ìç÷áíÞìáôá ðñÝðåé íá ãßíï\
íôáé ìüíï áðü
åîïõóéïäïôçìÝíá Üôïìá.
I II I
IRegolazioni e manutenzione su questa macchina devono essere fatti
solo da personale specializzato.
N NN N
NJustering eller vedlikehold på denne maskinen skall bare utføres av
kvalifiserte personell.
O OO O
OAanpassingen of onderhoud aan deze machine dient alleen
uitgevoerd te worden door bekwaam personeel.
P PP P
PAfinações ou manutenção nesta maquina, deverão ser efectuadas
sómente por pessoal qualificado.
S SS S
SJusteringar och underhåll på denna maskin skall endast utföras av
kvalificerad personal.
l ll l
lTätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden
omaava henkilökunta. 
						

							Page 46
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play 
meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings.  (Refer to
section 6-3  Test Mode page  46)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test and to change settings with\
in
a test.
COIN COUNTER
TEST SER VICE
ENTER
UP
SELECT DOWN 2 Amp Q/B 
(Coin Fuse)
PLAYER 1 
						

							Page 47 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
be displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of
the selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
to return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to
return to normal game mode.
The Test Switch must always be in the “OFF” position for normal game mode.
MENU
COIN OPTIONS............................Used to set the price of play
GAME OPTIONS............................Used to set the game options
I/O TEST............................Used for testing switches, and
control pots
MONITOR TEST............................Used for setting the monitor
SOUND TEST............................Used for setting the volume
ADS DATA............................Used to view bookkeeping
OTHERS............................Used for testing the PCB and
Initializing the control pots.
UP/DOWN : SELECT ENTER : ENTER 
						

							Page 48
6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game costand related settings. The following screen is displayed.
2. Use the Select Up/Down switch choose the required item then press the Enter button. The selected item will flash
3. Use the Enter button to change the setting of the flashing item. 
4. Select “EXIT” and press the Enter button to return to the menu screen.
Note:- The price of play on this machine is set within the Cashflow Coin\
 Mech. Ensure that the Game Cost is set to 1 Coin 1 Credit.
MET
INOITPIRCSE DTESYROTCAF
tsoCemaG)a
(9-1 elbattes-----stiderC
foreb
m
unrofderiuqersnio
C tiderC
1
nio
C
1
yalP
eerF)b
(ffO/nO-----snioctuohtiwelbaliavatiderC FFO
COIN OPTIONS [DEFAULT IN GREEN] 
GAME COST
1 COIN (S) 1 CREDIT ............................ (a)
FREE PLAY OFF ............................ (b)
EXIT
UP/DOWN : SELECT ENTER : ENTER 
						

							Page 49 6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the game
variables, the following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then
press the Enter button. The selected item will flash.
3. Use the Enter button to change the setting of the flashing item.
4. Select “EXIT” and press the Enter button to return to the menu
screen.
M E T INO I T P I R C S E DTE S Y R O T C A F
) a (em i t e m a g e h t s t e S) t r o h s ( D R A H , ) m u i d e m ( L A M R O N , ) g n o l ( Y S A EL A M R O N
) b (yt l u c i f f i D e m a G s u n o B s t e SDR A H d n a , L A M R O N , Y S A EL A M R O N
) c (h c a e r o t g n i t t e s y t l u c i f f i D
e m a g s u n o bD R A H d n a , L A M R O N , Y S A EL A M R O N
) d (t u o h t i w r o h t i w e m a g t e S
t i m i l e m i t) t i m i l e m i t o N ( F F O , ) ) a ( t a t e s t i m i l e m i T ( N ON O
) e (re y a l p f o t n i o p w e i Vm o r f w e i V ( D N I H E B , ) e m a g g n i r u d s e g n a h c ( O T U A
) w e i v s  r e y a l P ( E D I R , ) r e y a l p d n i h e bO T U A
) f (ta o b n i n w o h s s r e y a l P) n a m o w e n o ( N A M O W , ) n a m e n 0 ( N A M , ) o w t ( R I A PR I A P
) g (ed o m y b - d n a t s n i d n u o Sc i s u m o n ( F F O , ) y l n o e c i o v ( C M , ) e c i o v d n a c i s u m ( L L A
) e c i o v r oL L A
) h (ez i l a i t i n i e r o c s h g i Hd e n i a t e r s e m a N ( O N , ) f f o r e w o p t a d e r a e l c s e m a N ( S E Y
) y l e t a i d e m m i d e r a e l c s e m a N ( W O N , ) f f o r e w o p t aO N
GAME OPTIONS [DEFAULT IN GREEN]
TIME DIFFICULTY NORMAL................................. (a)
BURDEN GAME NORMAL................................. (b)
BONUS DIFFICULTY NORMAL................................. ( c )
TIME LIMIT ON................................. (d)
VIEW POINT AUTO................................. (e)
PLAYER CHARACTER AUTO................................. ( f )
ATTRACT SOUND ALL................................. ( g )
HI-SCORE INITIALIZE NO................................. (h)
EXIT
UP/DOWN : SELECT ENTER : ENTER 
						

							Page 50
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to test the control pots, swi\
tches and lamps. The following screen is displayed.
2. Use the Select Up/Down switch to  choose the required item then press the Enter button. The selected item will flash
3. Use the Enter button to change the setting of the item flashing. 
4. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a) Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
(c) Selecting this item allows all switches and control pots to be checked. (See 6-3-3-1 ‘Switch  Test’ page  50)
(d) Selecting this item allows the air springs to be tested. (See 6-3-3-2 ‘Ride  Test’ page  51)
I/O TEST
DIP 12345678 ................................ (a)
SWITCH & PADDLE ...................................... (b)
RIDE TEST ................................................. ( c )
EXIT 
UP/DOWN : SELECT ENTER : ENTER 
						

							Page 51 6-3-3-1 Switch and Paddle Test
1. Select “Switch Test” on the I/O menu screen and press enter to test
the switches. The following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT and
return to the I/O menu screen
(a) - (g) Displays current condition of each switch. ‘TEST’ is always ON. All
other switches OFF will change to ON each time the switch is
operated.
(h) When the paddles are pushed backwards or forwards, the number
will change. ‘OK’ will be displayed just before each paddle is pushed
fully forward.
(i) When the paddles are pushed up or down, the number will change.
‘OK’ will be displayed just before each paddle is pushed fully up.
(j) This test checks the rowing operation of the paddle. The indication
changes in a + (plus) value when you paddle forwards, and changes
in a - (minus) value when you paddle backwards.
SWITCH & PADDLE
TEST : ON.............................................. (a)
COIN : OFF.............................................. (b)
SERVICE : OFF.............................................. ( c )
S TART : OFF .............................................. (d)
UP SELECT : OFF.............................................. (e)
DOWN SELECT : OFF.............................................. ( f )
ENTER : OFF.............................................. (g)
HORIZONTAL : FFFF ––..................... (h)
VERTICAL : FFFF ––_______ ...................... (i)
THRUST : – ––––Q
–––– +...................... ( j )
UP + ENTER : EXIT