Namco Rapid River Operators Manual

							Page 32
4. MOVING THE MACHINE
This machine is fitted with castors to make it easier to move. Take care when 
moving the machine on an inclined surface.
The overall height of the machine is 2280mm. Take care of any overhead 
obstructions. (e.g. Light Fittings, Electric Cables etc.)
When moving the game, ensure that the game is dis-assembled into 3 parts\
: 
Monitor Assembly, Ride Assembly, and Header Assembly.
Note: The monitor assembly can be further dismantled by removing the pro\
jectorfrom the projector base.  (See section 5-1 page 36)
WARNING • NEVER turn the power to the machine ON until 
installation has been completed.
WARNING • In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a
securely connected earthed plug.
WARNING • So that customers are not injured , ensure that there is at least 500mm separation between other machines or
walls.
CAUTION • In  order to avoid damage to the machine due to mis-
operation, ensure that the voltage of the mains supply is
230volts AC.
5. INSTALLATION
Notes on Installation
NOTE • If the location site of this machine has a polished floor it is recommended that rubber pads are fitted under the level 
adjusters to prevent the machine sliding on the floor.
• In order to gain access to the Power Supply and CPU assemblies, make sure that the rear of the machine is
separated from a wall or other machine by at least 500mm.
• When installation is complete, it is imperative that the game
is initialized . (See section 7 page  56) 
						

							Page 33
Play Zone 
						

							Page 34
G
DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit
Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an
Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger Vibration.
5. An Plätzen, die nicht eben sind.
D
DENNE MASKINE ER KUN DESIGNET TIL INDENDØRSBRUG
INSTALLER IKKE MASKINEN PÅ FØLGENDE STEDER
1. Udendørs
2. Direkte sollys, steder med høj fugtighed el. støv, steder med vand udslip, i
nærheden af air-condition eller varme udstyr, steder med usædvanlig høj
el. kold temperatur.
3. Steder hvor den vil stå i vejen for nødudgange eller brandslukningsudstyr.
4. Ustabile steder eller steder med for store vibrationer.
5. Steder der ikke er plane.
ESTA MÁQUINA ESTA DISEÑADA ÚNICAMENTE PARA USO EN INTERIORES.
NO INSTALE LA MÁQUINA EN LOS SIGUIENTES LUGARES.
1. Exteriores.
2. Bajo luz solar directa, en lugares con polvo o humedad excesiva, lugares donde hay
filtraciones de agua, cerca de aparatos de calefacción o de aire acondicionado, lugares
con temperatura ambiente muy alta o muy baja.
3. Lugares donde la máquina obstruya salidas de emergencia o equipos de extinción de
incendios.
4. Suelos inestables o lugares con vibraciones excesivas.
5. Lugares con suelos no nivelados.
E c
This machine is designed for INDOOR USE ONLY.
Do not install in the following places.
1. Outdoors
2. Direct Sunlight, places with excessive humidity or dust, places where
there is water leakage, near air-conditioning or heating equipment, places
with excessive heat or cold temperature.
3. Places where it would be in the way of emergency exits or fire
extinguishing equipment.
4. Unstable places or places with excessive vibration.
5. Places that are not level.
6. This machine 
must not be cleaned with a water jet, or installed in an area
where a water jet could be used. 
						

							Page 35
F
K
I
N
O
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje,
nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.
 DEZE MACHINE IS ALLEEN VOOR GEBRUIK BINNENSHUIS ONTWORPEN
 INSTALLEER DE MACHINE NIET OP DE VOLGENDE PLAATSEN
1. Buiten
2. In direct zonlicht, op plaatsen met een zeer hoge vochtigheidsgraad of met veel stof, op
plaatsen waar een waterlek is, dichtbij airco’s of verwarmingsapparatuur, op plaatsen
met een zeer hoge of koude temperatuur.
3. Op plaatsen waar nooduitgangen of blusapparatuur worden geblokkeerd.
4. Op onstabiele plaatsen of plaatsen waar grote trillingen voorkomen.
5. Op plaatsen die niet vlak zijn.CETTE MACHINE EST DESTINEE UNIQUEMENT A UN USAGE INTERIEUR
NE PAS INSTALLER LA MACHINE DANS LES ENDROITS SUIVANTS
1. A l’extérieur.
2. Directement exposée au soleil, aux endroits excessivement humides ou poussiéreux,
aux endroits où il y a des risques de fuite d’eau, près de ventilateurs ou source de
chaleur, aux endroits très chauds ou froids.
3. Dans des zones de proximité des sorties de secours ou d’accès aux équipements
d’extinction du feu.
4. Dans des emplacements instables ou soumis à de fortes vibrations.
5. Dans des endroits dénivelés.
ÔÏ ÌÇ×ÁÍÇÌÁ ÅÉÍÁÉ Ó×ÅÄÉÁÓÌÅÍÏ ÃÉÁ ×ÑÇÓÇ ÓÅ ÅÓÙÔÅÑÉÊÏ ×ÙÑÏ\
 ÌÏÍÏ
ÌÇÍ ÔÏÐÏÈÅÔÇÓÅÔÅ ÔÏ ÌÇ×ÁÍÇÌÁ ÓÔÏÕÓ ÁÊÏËÏÕÈÏÕÓ ×ÙÑÏÕÓ
1. ÅîùôåñéêÜ
2. Áðåõèåßáò óôïí Þëéï,óå ìÝñç üðïõ õðÜñ÷åé õãñáóßá Þ óêüíç,ìÝñç üðïõ õðÜñ÷åé Üöèïíï íåñü,êïíôÜ
óå air-condition Þ Üëëïõ åßäïõò èÝñìáíóç,ìÝñç ìå õðåñâïëéêÞ õøçëÞ Þ ÷\
áìçëÞ èåñìïêñáóßá.
3. Óå ìÝñç üðïõ åìðïäßæïõí ìÝóá áíÜãêçò ð.÷. ðõñïóâåóôÞñåò Þ Üëëá.
4 Ìç óôáèåñÜ ìÝñç Þ ìÝñç ìå ðïëëïýò êñáäáóìïýò.
5. ÌÝñç ðïõ äåí åßíáé åðßðåäá.
QUESTA MACCHINA E’ PROGETTATA PER ESSERE USATA ESCLUSIVAMENTE
IN AMBIENTI INTERNI.
NON INSTALLARE LA MACCHINA NEI SEGUENTI LUOGHI.
1. In ambienti esterni.
2. Alla luce diretta del sole, in posti con eccesiva umidità o polvere, in luoghi dove ci siano
infiltrazioni d’acqua, vicino ad apparecchi di condizionamento d’aria oppure
riscaldamento, in posti eccessivamente caldi o freddi.
3. In luoghi dove potrebbe esserci un uscita di emergenza o un’attrezzatura per lo
spegnimento del fuoco.
4. In posti non stabili o con eccessive vibrazioni.
5. In luoghi non piani. 
						

							Page 36
P
l S
ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS
INTERIORES APENAS
NÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-
1. Exteriores.
2. `Luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de
água perto de ar condicionados ou equipamentos calorificos e locais com temperaturas
excessivamente quentes ou frias.
3. Locais aonde ficaria colocada no caminho de saidas de emergência ou equipamentos
extintores de fogo.
4. Locais estruturalmente instaveis ou locais com vibrações excessivas.
5. Locais não nivelados.
DENNA MASKIN ÄR AVSEDD ENBART FÖR INOMHUSBRUK
INSTALLERA EJ MASKINEN PÅ FÖLJANDE STÄLLEN
1. Utomhus
2. I direkt solsken, platser med extremt hög luftfuktighet eller damm, platser där det
förekommer vattenläckage, nära luftkonditionering eller värmeelement, i extremt hög
eller låg temperatur.
3. Platser där den skulle kunna vara i vägen för nödutgångar och
brandsläckningsutrustning.
4. Instabila ställen eller där stark vibration förekommer.
5. Platser med nivåskillnad.
TÄMÄ LAITE ON SUUNNITELTU VAIN SISÄKÄYTTÖÖN
ÄLÄ ASENNA LAITETTA SEURAAVIIN PAIKKOIHIN:
1. Ulkotilaan
2. Suoraan aurinkovaloon, kosteisiin tai pölyisiin paikkoihin, vesivuotopaikkojen
läheisyyteen, ilmanvaihto- tai lämmityslaitteen lähistölle tai paikkoihin, jossa on erittäin
kuumaa tai kylmää.
3. Varauloskäytävien, muiden pakoteiden tai tulensammutusvälineiden eteen.
4. Epävakaisiin tai täriseviin paikkoihin.
5. Kaltevalle alustalle. 
						

							Page 37
5-1 Removing the Monitor from the Monitor Base
The monitor is heavy (approx. 100kg). At least 4 people are required to lift the monitor from the monitor base.
1. Remove 6off Security screws (M5x30), and remove the front cover panel. 
2. Disconnect the connectors.
3. Remove 2off Hex head screws (M10x130), spring and special washer from the front underside of the monitor.
4. Remove 2off Pozi head screws (M5x30) and remove the cover bracket. 
						

							Page 38 5. Remove the rear door from the monitor base.
6. Remove 2 off Hex head screw (M10x130), spring and special washers
from the rear underside of the monitor.
7.  Carefully lift and remove the monitor from the base.
Note: Ensure that the monitor is kept level and avoid any knocks while lifting
or carrying the monitor. 
						

							Page 39
5-2 Fitting the Header Assembly
The Header Assembly has a forward centre of gravit y, so it is important that
at least 
two peopl e are used to fit or remove the Header Assembl y.
The fitting position of the Header Assembly is very high, and it is impo\
rtant 
that a means of reaching the height safel y, without stretching, is available.
(e.g. steps, step stools etc.)
1. Place the Header assembly on to the monitor cabinet and slide it backwards so that it engages under the retaining bracket.
2. Fix the Header asembly with two pozi head screws (with flat and spring washers) (M6x30). 
						

							Page 40 3. Remove two pozi head screws (with flat and spring washers) (M5x16), and
remove the connector cover.
4. Connect the connector of the Header assembly to the projector,and refit
the connector cover with the two pozi head screws (with flat and spring
washers) (M5x16). 
						

							Page 41 5-3 Joining the Ride Assy and Monitor Assy
1. Remove the four security screws (M5x12) on the ride assy, and remove
the joint cover.
2. Move the ride assy up to the projector cabinet and fit the four hex head
screws (M8x40).