Namco Rapid River Operators Manual

Page 42
3. Remove 8off Hex head screws (M10x20), and remove the four shipping
brackets.
4.  Refit the 8off Hex head screws previously removed.
5. Remove the four nuts (M8).
6. Place one shipping bracket (removed in step 3) on top of another and
retain each pair, for future use, on the studs with the four nuts (M8)
removed in step 5. 

Page 43 7. Connect the connectors and air tube.
8. Replace the joint cover removed in step 1.
Note: The air tube is a push fit. Ensure that the tube is pushed fully in when
fitting.
When removing the air tube push the blue ring of the connector in and
whilst holding it in, pull the air tube out.
If the compressor reservoir tank has air in it, a loud noise will be heard
as the air escapes when the air tube is removed.
9. When the machine is in its final position, lower the eight level adjusters,
(4 on the...

Page 44 5-4 Fitting the Paddles
1. Fit the blade assy into the paddle assy.
2. Adjust the angle of the blade so that the spring pin of the blade assy is
aligned with the screw hole of the paddle assy. Tighten the nut to fix the
blade assy.
3. Fit the grub screw (M6x10) into the screw hole of the paddle assy. 

Page 45
6. ADJUSTMENTS
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power
switch is located on the rear of the monitor cabinet.
G GG G
GAdjustment or maintenance on this machine should be carried out by
qualified personnel only.
D DD D
DEinstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.
l ll l
lJusteringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
E EE E
ELos ajustes y el...

Page 46
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play 
meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings.  (Refer to
section 6-3  Test Mode page  46)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test...

Page 47 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
be displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of
the selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
to return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to
return to normal game mode.
The Test Switch must always be in the “OFF” position for...

Page 48
6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game costand related settings. The following screen is displayed.
2. Use the Select Up/Down switch choose the required item then press the Enter button. The selected item will flash
3. Use the Enter button to change the setting of the flashing item. 
4. Select “EXIT” and press the Enter button to return to the menu screen.
Note:- The price of play on this machine is set within the Cashflow Coin\
 Mech. Ensure that the Game...

Page 49 6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the game
variables, the following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then
press the Enter button. The selected item will flash.
3. Use the Enter button to change the setting of the flashing item.
4. Select “EXIT” and press the Enter button to return to the menu
screen.
M E T INO I T P I R C S E DTE S Y R O T C A F
) a (em i t e m a g e h t s t e S) t r o h s ( D R A H , ) m u i d e...

Page 50
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to test the control pots, swi\
tches and lamps. The following screen is displayed.
2. Use the Select Up/Down switch to  choose the required item then press the Enter button. The selected item will flash
3. Use the Enter button to change the setting of the item flashing. 
4. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a) Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF....

Page 51 6-3-3-1 Switch and Paddle Test
1. Select “Switch Test” on the I/O menu screen and press enter to test
the switches. The following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT and
return to the I/O menu screen
(a) - (g) Displays current condition of each switch. ‘TEST’ is always ON. All
other switches OFF will change to ON each time the switch is
operated.
(h) When the paddles are pushed backwards...