Namco Rapid River Operators Manual

Page 32
4. MOVING THE MACHINE
This machine is fitted with castors to make it easier to move. Take care when 
moving the machine on an inclined surface.
The overall height of the machine is 2280mm. Take care of any overhead 
obstructions. (e.g. Light Fittings, Electric Cables etc.)
When moving the game, ensure that the game is dis-assembled into 3 parts\
: 
Monitor Assembly, Ride Assembly, and Header Assembly.
Note: The monitor assembly can be further dismantled by removing the pro\
jectorfrom the...

Page 33
Play Zone 

Page 34
G
DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit
Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an
Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger...

Page 35
F
K
I
N
O
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje,
nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.
 DEZE MACHINE IS ALLEEN VOOR...

Page 36
P
l S
ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS
INTERIORES APENAS
NÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-
1. Exteriores.
2. `Luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de
água perto de ar condicionados ou equipamentos calorificos e locais com temperaturas
excessivamente quentes ou frias.
3. Locais aonde ficaria colocada no caminho de saidas de emergência ou equipamentos
extintores de fogo.
4. Locais estruturalmente instaveis ou locais com...

Page 37
5-1 Removing the Monitor from the Monitor Base
The monitor is heavy (approx. 100kg). At least 4 people are required to lift the monitor from the monitor base.
1. Remove 6off Security screws (M5x30), and remove the front cover panel. 
2. Disconnect the connectors.
3. Remove 2off Hex head screws (M10x130), spring and special washer from the front underside of the monitor.
4. Remove 2off Pozi head screws (M5x30) and remove the cover bracket. 

Page 38 5. Remove the rear door from the monitor base.
6. Remove 2 off Hex head screw (M10x130), spring and special washers
from the rear underside of the monitor.
7.  Carefully lift and remove the monitor from the base.
Note: Ensure that the monitor is kept level and avoid any knocks while lifting
or carrying the monitor. 

Page 39
5-2 Fitting the Header Assembly
The Header Assembly has a forward centre of gravit y, so it is important that
at least 
two peopl e are used to fit or remove the Header Assembl y.
The fitting position of the Header Assembly is very high, and it is impo\
rtant 
that a means of reaching the height safel y, without stretching, is available.
(e.g. steps, step stools etc.)
1. Place the Header assembly on to the monitor cabinet and slide it backwards so that it engages under the retaining bracket.
2....

Page 40 3. Remove two pozi head screws (with flat and spring washers) (M5x16), and
remove the connector cover.
4. Connect the connector of the Header assembly to the projector,and refit
the connector cover with the two pozi head screws (with flat and spring
washers) (M5x16). 

Page 41 5-3 Joining the Ride Assy and Monitor Assy
1. Remove the four security screws (M5x12) on the ride assy, and remove
the joint cover.
2. Move the ride assy up to the projector cabinet and fit the four hex head
screws (M8x40).