Namco Gunmen Wars Service Manual


 6-3-3-6 Camera Check
1. Select ‘CAMERA CHECK’ from the I/O Test Screen. The following
screen is displayed:-

In the CAMERA CHECK Screen, the current view of the camera is
displayed in the centre box.
(a) MIRROR/PHOTO
By pressing the Service Switch, the image from the camera is frozen
on the screen and the word MIRROR, just below the image box,
changes to PHOTO. This is the image that would be used during the
game.
Pressing the Service Switch again rever ts back to current camera
image, and the...

 (c) TINT  ADUST
This setting is used to adjust the colour tint of the image.
The colour tint of the image is automatically adjusted to the optimum value
by the system, but this item allows the colour tint level to be set manually.
Select this item and press the ENTER button. Use the Select UP/DOWN
switch to increase or decrease the red tint. The red tint can be increased
or decreased by three levels each.
Press the ENTER button to store the new setting and to exit this mode.
(d) V  POSITION
This...

 6-3-4 Monitor Test
1. Select “MONITOR TEST” on the menu screen to test and adjust the
Monitor. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button. To return to the Monitor Test Menu from a test pattern
press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu screen.
Note:   Items (c) and (i) are not used on this game.
MONITOR TEST
GRADATION PATTERN..................................... (a)...

 6-3-5 Sound Test
1. Select “SOUND TEST” on the menu screen to test the audio and adjust
the volume settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button.
3. Use the Up/Down switch to change the setting.
4. Press the Enter button to return to item select mode
4. Select “EXIT” and press the Enter button to return to the menu screen.
SOUND  TEST

VOLUMEALL SP............................ (a)
FRONT L SP (00~64)...

Page 55 6-3-6 ADS  Data
By selecting ADS Data from the menu screen, all of the bookkeeping
details can be read and/or reset.
6-3-7Others
1. Select “OTHERS” on the menu screen. The following screen is displayed.
2. Use the Select Up/Down switch choose the required item then press the
Enter button.
3. Select “EXIT” and press the Enter button to return to the menu screen.
(a,) Displays  game  software  version.
(b) Not used on this game
(c) Used to test the PCB. (this function is only for factory testing)...


7. INITIALIZATION
Adjustments when Replacing Parts
The following operation 
must always be performed after replacing the Game
PCB, Rom, or Control Potentiometers.
The game will not operate correctly if these adjustments are not made.
1. Slide the TEST switch ON while pressing the SERVICE switch . The
following screen is displayed.
GUN  INITIALIZE
AIM  AT  CENTER  OF THE  CROSS
AND  PUSH  SERVICE  BUTTON
GUN YAWING
SLIDE FORWARD
0000
LEFTRIGHT
0000 0000
BACK
0000
TRIGGER :  ADJUST  SLIDE  AND...

 
 	



G






















7 1







7&&

	


(
8

	.
$


9
D	

 	

!
#

$
#
%
&

$	

:
;	

 	
8&

.
1
9
<

=%(
	%	

c	

$	



(...


OAanpassingen of onderhoud aan deze machine dient alleen
uitgevoerd te worden door bekwaam personeel.
Zorg ervoor dat de machine UITgeschakeld is voordat er enig
onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)
PAfinações ou manutenção nesta maquina, deverão ser efectuadas
sómente por pessoal qualificado.
Certifique-se que a maquina se encontra desligada sempre que
iniciar qualquer tipo de trabalho de manutenção. (identifação de
avarias, reparação etc.)
SJusteringar och underhåll...

 8-1 Greasing the Gun Assembly
Greasing should be performed every six months.
1. Remove 4off security screw (M5x16) and remove the Gun Vac-form
Upper,
2. Remove 15off security screw (M5x20) and remove the Gun Vac-form
Lower.
3. Grease the circumfrance of the bearings.
Recommended grease : Castrol LM30 or equivalent.
Security screw (M5 × 16)Security screw (M5 × 20)
Security screw (M5 × 16)
Gun Vac-form
   Upper
Gun Vac-form LowerGun Vac-form
   UpperSecurity screw
 (M5 × 20)
Security screw
 (M5 ×...


	 8-2 Replacing the Fluorescent Lamp or Starter
1. Remove 6off security screw (M5x16) and remove the Lower Retaining
bracket  and  Header  Acrylic.
2. Replace the fluorescent lamp and/or starter.
3. Reassemble in reverse order.
Security screw (M5 x 16)
Lower Retaining Brkt Header Acrylic
Fluorescent lamp
Starter