Namco Gunmen Wars Service Manual



8-9 Replacing the Left / Right Potentiometer
1. Remo ve  \bhe  Gun  V ac- Form s.  ( See  8-1  page  59 )
2 . Remo ve  \bhe  gun  F ram e.  ( See  8-3  page  61 )
3 . Remove \bhe slide covers \H(S), (R) and (L). ( See 8-7 page 68).
4 . Disconnec\b  \bhe  lef\b/ righ\b  slide  po\ben\biome\ber  connec\bo r.  ( See  8- 8 page  70 )
5 Remove 6off flange socke\b heads screws (M6x12) and remove \bhe gun assembly by lif\bing i\b s\braigh\b u\Hp.
6. Remove \bhe cup screw (S) (M4x10), loosen \bhe double...


7. Replace \bhe po\ben\biome\ber. 
Note: When\brepl\fcing\bthe\bpotentiometer\bensure\bth\ft\bthe\bdouble\bpoint\bscrew
(M4x6)\beng\fges\bon\bthe\bfl\ft\bof\bthe\bpotentiometer\bsh\fft,\b\fnd\bth\ft\bthe
correct\bcolour\bwires\b\fre\bconnected\bto\bthe\bcorrect\btermin\fls.
8. Reasemble in reverse order. 
êfOTE: After replacing the potentiometer REIêfITIALIZE the game. (see  section  7  page  56   ).
Connector
Pot bracket
Potentiometer Plain washerSpring washer
Nut
Whi/Red
Whi/GryWhi/Blk
123 

\b
8-10 Replacing the Monitor
The monitor  weighs  approx  40kg.  Ensure  that  at  least  two  people
are  a vailable  to  rem ove  the  monito r.
1 . Sepera\be  \bhe  F ron\b  assem bly  from  \bhe  Moni\bor  \fabine\b .  ( See  5-1  page  39 )
2. Loosen \bhe lower 2off pozi\H head screws (M5x25) on \bhe\H main\benance panel on \bhe rear of \bhe moni\bor cabine\b, remove \bhe 2off upper pozi head 
screws (M5x25), and remove \bhe main\benance panel.
3. Disconnec\b \bhe moni\bor con\Hnec\bors and...

 4. Remove 10off security screw (M5x16) and remove the Monitor Vac-form.
Security screw (M5 × 16)
Security screw (M5 × 16)
Security screw (M5 × 16)
Monitor Vac-form 

 5. Remove 4off pozi head screws (M8x25), with spring and special flat
washers.
6. Tilt the monitor forward from the top and lift the monitor out of the cabinet.
7. Reassemble in reverse order.
Pozi head screws (M8x25)
(with flat and spring washers)
Pozi head screws (M8x25)
(with flat and spring washers)Washer 


 8-11 Replacing the Camera
1. Remove 6off Security screw (M5x16).
2. Lift the Camera assemblyy forward carefully, and disconnect the
connector.
3. Remove  the  Camera  assembly.
4. Remove 4off pozi head screw (M4x10) and remove the Camera Housing.
5. Remove the Camera PCB by carefully pushing the retaining clips outward.
6. Reassemble in reverse order.
Camera Assy
Security screw (M5 × 16) Connector
Pozi head screw (M4 x 10)
Clip
Camera Camera housing 


4
3212223
1
10
7
8
9
2
9. PARTS
m e t Ino i t p i r c s e DoN t r a P
1mr o f - c a V d n u o r r u S r o t i n o M4 4 9 0 0 0 6 4
2"8 2 r a n a l P m u i d e M o l o P x e r a t n a H - r o t i n o M1 0 0 0 0 0 4 8
3el l i r G r e k a e p S2 5 9 0 0 0 6 4
4"½ 4 - r e k a e p s d u o L6 0 0 0 0 0 2 6
7te k c a r B g n i c r o f n i e R l a n r e t n I7 4 9 0 0 0 6 4
8)S H L ( l a c e D e d i S2 8 4 0 0 0 0 4
9)S H R ( l a c e D e d i S3 8 4 0 0 0 0 4
0 1)S H R / S H L ( l a c e D t n o r...


22
131118
2019
2324
21
5
29
301631
17
15
12
2
14
(Opposite       side)
Gun  Cabinet 


m e t Ino i t p i r c s e DoN t r a P
2)S H R / S H L ( e b u T t r o p p u S r e d a e H3 5 9 0 0 0 6 4
4At e k c a r B g n i c r o f n i e R e b u T4 5 9 0 0 0 6 4
5te k c a r B t n i o J t e n i b a C n u G5 5 9 0 0 0 6 4
1 1mr o f - c a V p o T n u G0 6 9 0 0 0 6 4
2 1re w o L m r o f - c a V n u G1 6 9 0 0 0 6 4
3 1mr o F - c a V r e v o C d r a w r o F n u G2 6 9 0 0 0 6 4
4 1SH L - l a c e D e d i S t e n i b a C6 8 4 0 0 0 0 4
5 1SH R - l a c e D e d i s t e n i b a C7 8 4 0 0 0 0 4
6 1la...

	
1
3
2
m e t Ino i t p i r c s e DoN t r a P
1te k c a r B g n i t n u o M a r e m a C1 5 9 0 0 0 6 4
2la c e D ' m a c m a N ' a r e m a C5 8 4 0 0 0 0 4
3yl b m e s s A a r e m a C0 5 0 - 6 8 6 - O R X
Camera Assy