Namco Gunmen Wars Service Manual



3. MAJOR COMPONENTS     


4. MOVING THE MACHINE
Security screw (M5 × 16)
Security screw (M5 × 16)Frame cover
4-1 Removing the Header Assy and Side Poles
The header assembly is heavy, approx 20kg. ensure that at least 2 people are
available to remove the header assy and that there is sufficient space to work.
1. Remove the 6off security screws (M5x16) and remove the frame cover.
This machine is fitted with castors to make it easier to move. Take care when
moving the machine on an inclined surface.
The overall height of the...


Connector
Hex head screw (M8x20)
Header assy
Connector
2. Disconnect  the  connector.
3. Ensure that the header assy is being held firmly to prevent it falling and
remove the 4off hex head set screws (M8x20), and remove the header
assembly. 

 4. Disconnect the connector inside the Gun Base assembly.
5. Remove 4off hex head screws (M8x45) and remove the Side Pole.
Note: The side pole is 1.92m high and approx 10kg. Ensure that at least
two people are available to remove the side pole, and that there is
adequate  workspace.
6. Repeat to remove the other Side Pole.
7. Reassemble in reverse order.
Gun base assembly
Connector
Hex head screw (M8 × 45)
Hext head screw (M8 × 45)Side pole 

\b\f
5. IêfSTALLATIOêf
êfotes on Installation
NOTE • If \bhe loca\bion si\be of \bhis machine has a polished floor i\b is recommended  \bha\b  rubber  pads  are  fi\b\bed  under  \bhe  level 
adjus\bers \bo preven\b \bhe machine sliding on \bhe floor.
• In  order  \bo  gain  access  \bo  \bhe  Power  Supply  and  \fPU assemblies,  make  sure  \bha\b  \bhe  rear  of  \bhe  machine  is
separa\bed from a wall or o\bher machine by a\b leas\b 500mm.
• When ins\balla\bion is comple\be, i\b is impera\bive...




DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN GESCHLOSSENEN
RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit
Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an
Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger...






	
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje, nære
luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.
 DEZE MACHINE IS ALLEEN VOOR...




 
ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS
INTERIORES APENAS
NÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-
1. Exteriores.
2. `Luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de
água perto de ar condicionados ou equipamentos calorificos e locais com temperaturas
excessivamente quentes ou frias.
3. Locais aonde ficaria colocada no caminho de saidas de emergência ou equipamentos
extintores de fogo.
4. Locais estruturalmente instaveis ou locais com...

 2. Push the Front assembly up to the monitor assembly completely, taking
care not to trap any wires.
3. Remove the rear door from the Monitor assembly.
4. Fit 6off hex head screws (M10x50) to retain the Front assembly to the
Monitor  assembly.
Hex head screw (M10×50)
5-1 Fitting the Front assy to the Monitor assy
1. Place the Front assembly close to the Monitor assembly and connect the
connectors.
Connector
ConnectorControl Assy Front Assy
5. When the assembled game is in its final position,...

Page 40
5-2. Lin\bing t\fo Machines
1. Switc\b bot\b \fac\bines off. 
2. Re\fove 2off pozi \bead screws (M5x12) and re\fove t\be Link Cover Bracket.
3. Fit t\be Link Cable (supplied) as s\bown in t\be following diagra\f 
4. Refit t\be Link Cover Bracket wit\b t\be 2off pozi \bead screws (M5x12). 
5 . See section 6-3-2 pa\oge  42 to set the game PCB I\oD. Failure to set the
ID \fill prevent the games operating correctly.
Rear of t\be front asse\a\fbly (1) Rear of t\be asse\fbly (2)