Namco Aqua Jet Operators Manual

Page PB 5-1 Removing the Projector from the Projector Base.
WARNING • Make sure that the power is turned OFF before
commencing any work.
WARNING • The projector Assy weighs approx. 100kg. At least
four people should be used to remove it from it’s
base.
CAUTION • The projector assy. is a precision assembly and should be
handled with extreme care, avoiding heavy knocks.
1. Remove the six security screws (M5x30) and remove the front door.
2. Disconnect the two projector connectors.
3. Remove the four...

Page 15
WARNING After the four hexagonal bolts have been removed, the
projector is only resting on the base. Take care that the
projector is not accidentally knocked or moved to prevent
the projector falling and causing injury. 4. Remove the two security screws (M5x30) and remove the small cover.
5. Remove the two pozi head screws (M5x30), unlock and remove the back
door only enough to be able to disconnect the fan connector.
6. Disconnect the fan connector and remove the back door fully.
7. Remove the...

Page PB 5-2 Fitting the Header Assembly
1. Place the Header Assembly on top of the monitor.
2. Lift the right end of the Header Assembly (as viewed from the front), and
connect the connector to the top of the monitor. (Ensure that a second
person prevents the Header Assembly from falling.)
3. Slide the Header Assembly towards the back of the monitor until it is fully
engaged in the locating bracket, taking care not to trap any wires.
4. Fasten the Header Assembly with the 3off M6x30 Hex head screws,...

Page 17 5-3 Connecting the Ride Assy to the Front Assy.
1. Push the Ride Assembly close to the Front Assy.
2. Connect the three connectors and the air tube.
3. Push the Ride Assy fully up to the Front assy, taking care not to trap any
wires.
3. Fit the Joint Brackets, finger tight, to the Front Assy using 4off Hex Head
Set Screws (M8x60), Spring and Flat Washers for each bracket. When all
screws have been located, tighten all the screws fully. 

Page PB 5-4 Assembling the Coin Tower
1. Connect the connector and place the coin tower on to the base assembly.
2. Attach the coin tower to the base, taking care not to trap any wires, using
the nine security button head screws (M10x25), flat and spring washers.
NOTE:- Ensure that the two security screws are fitted to the inside of the
cash box area.
3. Fit the cashbox plate to the inside of the coin tower using four pozi head
screws (M4x12), spring and flat washers.
4. Place the instruction panel into...

Page 19
5-5 Adjusting the Projector
Due to vibration during moving and assembly of the machine, the projector
convergence may require adjustment. If this is necessary, adjust the projector
using the following procedure.
For details on how to adjust the projector, refer to the “Projector Adjustment
Manual”.
NOTE:
• If the correct adjustment procedure is not followed, or the wrong buttons
are pressed, it may be impossible to return the projector to its normal
condition.
• The details for adjusting the...

Page PB
6. ADJUSTMENTS
6-1 Turning on the PowerAfter the machine has been installed, turn ON the power. The Power switch is 
located on the rear of the Main cabinet.  (See section 3 “Major Components”
(page 3).)
6-2 Adjustment Switches The adjustment switches are located inside the coin door. 
1. Service Switch Press this switch to obtain game credits without incrementing the play m\
eters.
2. Test Switch Slide this switch “ON” to enter test mode. 
Test mode allows game testing and the changing of game...

Page 21
6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Sc\
reen” will be displayed on the monitor.
2. Select the test required by moving the control handle up or down. The co\
lour of the selected test will change to red and blink.
3. Enter the selected test by pressing the start button. Select “EXIT”\
 to return to the “Menu Screen”
4. After testing is completed, ensure that the test switch is returned to t\
he “OFF” position to return to game mode.
The T est Switch must...

Page PB 6-3-1 Coin Options
a. Select item (1) “COIN OPTIONS” on the menu screen, to set the
game cost and related settings.
b. Move the Control Arm up or down to select the required item then
press the start button.
c. Press the start button to change the settings.
d. Select “EXIT” and press the start button to return to the menu
screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech. Ensure
that the Coin Options on the screen are set as shown in the following table.
COIN...

Page 23
6-3-2 Game  Options
a. Select item (2) “GAME OPTIONS” on the menu screen to set the game options.
b. Move the Control Arm up or down to select the required item. 
c. Press the Start button to change the settings. The settings will change each time the start button is pressed.
d. Select “EXIT” and press the start button to return to the menu screen.
GAME OPTIONS [DEFAULT IN GREEN] 
GAME TIME STD C ..................... (a)
EXP C
SOUND IN ATTRACT ON ..................... (b)
AUTO HI SCORE...