Namco Aqua Jet Operators Manual
Here you can view all the pages of manual Namco Aqua Jet Operators Manual. The Namco manuals for Games are available online for free. You can easily download all the documents as PDF.
Page 31
Page PB 4) Remove the potentiometer from the mounting bracket and replace with a new potentiometer. 5) Re-assemble in reverse order. NOTE: When refitting the potentiometer and bracket ensure that the grub screw engages on the flat of the potentiometer shaft, and the notch in the mounting bracket engages on the pin. 6) Re-initialize the game. (Refer to section 7 ‘Initialization’) 8-2-2 Removing the Tank WARNING • Make sure that the power is turned OFF before commencing any work. 1) Remove the four...
Page 32
![Page 32
Page 35
8-2-3 Replacing Solenoid Valve A
WARNING • Make sure that the power is turned OFF before
commencing any work.
1) Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’
2) Disconnect the connector.
3) Push the blue release of the elbow union in, and while holding it in, pull out the air tube. (There will be a loud noise as the air pressure \
is
released.)
4) Remove the two pozi head screws (M4x35) and remove the solenoid valve A.
5) Remove the elbow union, half union and silencer from...](http://img.usermanuals.tech/thumb/5509/60432/w300_aqua-jet-operator-s-english_d-31.png "Page 32
Page 35
8-2-3 Replacing Solenoid Valve A
WARNING • Make sure that the power is turned OFF before
commencing any work.
1) Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’
2) Disconnect the connector.
3) Push the blue release of the elbow union in, and while holding it in, pull out the air tube. (There will be a loud noise as the air pressure \
is
released.)
4) Remove the two pozi head screws (M4x35) and remove the solenoid valve A.
5) Remove the elbow union, half union and silencer from...")
Page 35 8-2-3 Replacing Solenoid Valve A WARNING • Make sure that the power is turned OFF before commencing any work. 1) Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’ 2) Disconnect the connector. 3) Push the blue release of the elbow union in, and while holding it in, pull out the air tube. (There will be a loud noise as the air pressure \ is released.) 4) Remove the two pozi head screws (M4x35) and remove the solenoid valve A. 5) Remove the elbow union, half union and silencer from...
Page 33
![Page 33
Page PB
8-2-
4Replacing Solenoid Valve B
WARNING • Make sure that the power is turned OFF before commencing any work.
1) Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’
2) Disconnect the connector.
3) Push the blue release of the elbow union in, and while holding it in, pull out the air tube. (There will be a loud noise as the air pressure \
is
released.)
4) Remove the two pozi head screws (M4x35) and remove the solenoid valve B.
5) Remove the half union, taper-screw plug and silencer...](http://img.usermanuals.tech/thumb/5509/60432/w300_aqua-jet-operator-s-english_d-32.png "Page 33
Page PB
8-2-
4Replacing Solenoid Valve B
WARNING • Make sure that the power is turned OFF before commencing any work.
1) Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’
2) Disconnect the connector.
3) Push the blue release of the elbow union in, and while holding it in, pull out the air tube. (There will be a loud noise as the air pressure \
is
released.)
4) Remove the two pozi head screws (M4x35) and remove the solenoid valve B.
5) Remove the half union, taper-screw plug and silencer...")
Page PB 8-2- 4Replacing Solenoid Valve B WARNING • Make sure that the power is turned OFF before commencing any work. 1) Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’ 2) Disconnect the connector. 3) Push the blue release of the elbow union in, and while holding it in, pull out the air tube. (There will be a loud noise as the air pressure \ is released.) 4) Remove the two pozi head screws (M4x35) and remove the solenoid valve B. 5) Remove the half union, taper-screw plug and silencer...
Page 34
Page 37 8-3 Control Arm Assembly 8-3-1 Replacing the Accelerator Potentiometer WARNING • Make sure that the power is turned OFF before commencing any work. 1) Remove the four security screws (M5x12) and remove the accelerator cover. 3) Disconnect the connector. Loosen the grub screw (M3x5) and remove the potentiometer complete with its mounting bracket. 4) Remove the potentiometer from the mounting bracket and replace with a new potentiometer. 5) Re-assemble in reverse order. NOTE: When refitting the...
Page 35
Page PB 8-3-2 Replacing the Control Arm Potentiometer WARNING • Make sure that the power is turned OFF before commencing any work. 1) Remove the tank. (Refer to section 8-2-2 ‘Removing the Tank’). 3) Disconnect the connector. Loosen the grub screw (M4x5) and remove the potentiometer complete with its mounting bracket. 4) Remove the potentiometer from the mounting bracket and replace with a new potentiometer. 5) Re-assemble in reverse order. NOTE: When refitting the potentiometer and bracket ensure...
Page 36
Page 39 8-3-3 Replacing the Start Switch or Lamp WARNING • Make sure that the power is turned OFF before commencing any work. 1) Remove the eight security screws (M5x12) and lift the top vac-form sufficiently to remove the switch and lamp from the push button. 2) Remove the top vac-form. 3) Replace the lamp or switch. 4) Re-assemble in reverse order.
Page 37
Page PB 8-4 Header Assembly 8-4-1 Replacing the Fluorescent Lamp or Starter WARNING • Make sure that the power is turned OFF before commencing any work. WARNING • The Header Assembly is very high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stools etc.) WARNING • The fluorescent lamp may be hot, take care when handling. 1) Remove the four security screws (M5x20), and remove the acrylic sign board. 2) Replace the fluorescent lamp or...
Page 38
Page 41 9. PARTS ITEMDESCRIPTIONPART No 1HEADER CABINET 37100110 2LOUDSPEAKER GRILLE 46000083 4HEADER ACRYLIC 30000234 5ACRYLIC RETAINING BRACKET 46000084 E1FLOURESCENT TUBE 18 15W 64500009 E3LOUDSPEAKER 5½ FULL RANGE 62000065 E4STARTER 240v 4-80W UNIVERSAL 63000000 E5STARTER HOLDER 64800001 B1 M6x16 HEX HEAD SET SCREW - BZP 26500311 M6 SPRING WASHER - BZP 28000028 M6 FLAT WASHER - BZP 28000166 B2 M4x16 PZ PAN HEAD - BLACK 26300294 M4 SPRING WASHER - BLACK 28000127 M4 FLAT WASHER - BLACK28000132...
Page 39
Page 42 Coin Tower ITEMDESCRIPTIONPART No 1COIN TOWER TOP VAC-FORM46000057 2INSTRUCTION DECAL SUPPORT BRACKET46000146 3PLAY INSTRUCTION DECAL - ACRYLIC30000235 5WOODEN CASHBOX37100093 6M12 ADJUSABLE FOOT88300311 73.5-6v METER - PANEL MOUNT65000002 8MINIATURE SLIDE SWITCH - DPCO60000023 9SERVICE SWITCH 7mm RED - F42460000059 B1No8x½ PZ CSK WOODSCREW - BZP26100265 B2M3x10 PZ PAN HEAD - BZP26300067 B7M5x16 SECURITY BUTTON HEAD - SUS26300032 B8M5x20 SECURITY BUTTON HEAD - SUS26300039 B9M5x14 RAWLNUT27000153
Page 40
Page 43 Cabinet Base ITEMDESCRIPTIONPART No 1INTERLOCK SWITCH6000006 2INTERLOCK SWITCH COVER39000028 3SCHAFFNER 10A DOUBLE FUSED MAINS IN FILTER62500011 4SHAFFNER BOOT 1B366000017 510A 20mm FUSE63500705 6SWIVEL CASTOR 75mm59000005 7M16 ADJUSTABLE FOOT88300079 8CONDENSATE BOTTLE 0.5ltr46000079 9WOODEN BLANKING STRIP37100109 10AQUA JET SUPER SYSTEM 22 PCB ASSYXAJ-PCB 114 CHANNEL AMP PCB - SUPER SYSTEM 22XCYB-AMPCB 12LAMP DRIVER PCB - SINGLE CHANNEL46000020 133 CHANNEL AMPLIFIER - Ver346000036 14ASTEC...