Namco Alpine Racer 2 Operators Manual

							Page 32 6-5 Initialization After Replacing Parts
Initialization must be performed after replacing the game PC board, Rom or Step
Controls. If initialization is not performed, the game will not function correctly.
During initialization, ensure that the step edges are level.
1. Select Step Adjust from the I/O Test menu. The following screen will appear on
the monitor.
2. Ensure that the skis are in the centre and level, then press the service button.
INITIALIZE COMPLETE will appear on the monitor display.
3. Select EXIT to return to the Main Menu Screen.
STEP ADJUST
SWING0000h AD0 0000h CENTER
EDGE 0000h AD1 0000h CENTER
INITIALIZE COMPLETED
PUSH SERVICE SWITCH TO RESET
: EXIT 
						

							Page 33 In order to prevent injury or electric shock to service personnel, ensure that
the MAIN POWER IS OFF before attempting any maintenance.
Before performing any work not described in this manual, be sure to contact
your distributor to receive instructions or answers to questions.
Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß der
Netzstecker gezogen werden.
Bei Arbeiten, die nicht in diesem Handbuch beschrieben werden, muß vorher
der Händler zu Rate gezogen werden, da sonst keinerlei Haftung bei
Beschädigungen und Verletzungen übernommen wird.
S’assurer que linterrupteur soit sor OFF avant de commencer tout travail de
maintenance (localisation dune panne, rèparations, etc.)
Si dans ce manuel il manque une information pour réaliser un quelconque
travail, contacter votre distributeur, car aucune responsabilité ne sera
acceptée en cas de domage ou de blessure.
Varmista, että laite on kytketty POIS PÄÄLTÄ ennen työn aloittamista.
Ota yhteyttä maahantuojaan ohjeita varten, jos joudut tekemään työtehtäviä,
joita ei ole esitelty huoltokirjassa, muuten vastuuta vioista tai
loukkaantumisista ei ole.
7-1 Replacing the Push Button Switch or Lamp
1. Remove the ten security head screws (M5x12)
and remove both side vac-forms.
2. Remove the four security head screws (M5x12)
and remove the play panel only sufficient to
disconnect the connector, taking care not to
strain any wires.
G B
D
F
S F
7. MAINTENANCE 
						

							Page 34 7-2 Replacing the Fluorescent Tube
1) Remove the two security head screws (M5x12) and remove the acrylic retaining
bracket.
2) Remove the header acrylic
3) Replace the fluorescent tube.
4) Reassemble in reverse order.
Warning The fluorescent tube may be hot take care when handling the tube.
3. Remove the lamp/switch assembly by
pulling it away from the switch body.
Replace the lamp or switch. 
						

							Page 35 7-3 Replacing the Edge Potentiometer
1. Remove the four security head screws (M5x12) and remove the step front vac-
form.
2. Remove the two hex head screws (M6x16) and remove the cover plate.
3. Disconnect the potentiometer connector.
4. Loosen the hex socket head set screw and remove the potentiometer complete
with bracket.
5. Replace the potentiometer taking care that the wires are re-soldered to the
correct terminals.
Note: Ensure that the lug on the potentiometer is engaged in the hole in the bracket
when refitting the potentiometer. 
						

							Page 36 7-4 Replacing the Swing Potentiometer
1. Remove the four security head screws (M5x12). Loosen the two security head
screws (M5x12) and remove the base front cover.
2. Disconnect the potentiometer connector.
3. Loosen the hex socket head set screw (M4x8) and remove the potentiometer
complete with bracket.
4. Replace the potentiometer taking care that the wires are re-soldered to the
correct terminals.
Note: Ensure that the lug on the potentiometer is engaged in the hole in the bracket
when refitting the potentiometer. 
						

							Page 37
8. PARTS
4 5 678910
11
16
17
18
19
21
1
2
312
13
14
15
20 
						

							Page 38
m e t Ino i t p i r c s e DoN t r a P
12r e c a R e n i p l A - y l b m e s s A B C PB C P 2 R A - R A X
2A0 3 V 5 U S P M S 0 0 4 3 - 1 0 3 A S c e t s A8 0 0 0 0 0 3 8
3re y a l P e n O B C P k n i L- P K N I L - 2 R A X
B C
4to o F e l b a t s u j d A 5 9 x 6 1 M9 7 0 0 0 3 8 8
5y s s A r e t l i F n I - s n i a M r e n f f a h c S0 1 0 0 0 5 2 6
t o o B r e n f f a h c S7 1 0 0 0 0 6 6
6h c t i w S k c o l r e t n I6 0 0 0 0 0 0 6
r e v o C h c t i w S k c o l r e t n I8 2 0 0 0 0 9 3
73r e V r e i f i l p m A l e n n a h C 36 3 0 0 0 0 6 4
8SH L - l a c e D m r o f - c a V e d i S4 8 1 0 0 0 6 4
9SH R - l a c e D m r o F - c a V e d i S5 8 1 0 0 0 6 4
0 1ci l y r c A r e d a e H3 4 0 0 0 0 0 3
1 1SH L - m r o F - c a V e d i S g n i s u o H r o t i n o M4 8 1 0 0 0 6 4
2 1tt a w 5 1  8 1 e b u T t n e c s e r o u l F9 0 0 0 0 5 4 6
3 1la s r e v i n U w 0 8 - 4 v 0 4 2 r e t r a t S0 0 0 0 0 0 3 6
4 1ek o h C0 0 0 0 0 3 3 6
5 1SH R - m r o F - c a V e d i S g n i s u o H r o t i n o M5 8 1 0 0 0 6 4
6 1mr o F - c a V r o t i n o M6 8 1 0 0 0 6 4
7 1ro t i n o M o l o P  8 2 x e r a t n a H6 2 0 0 0 0 4 8
8 1mr o F - c a V r o o D n i o C1 9 1 0 0 0 6 4
9 1mm 5 7 - r o t s a C l e v i w S5 0 0 0 0 0 9 5
0 2ss a B  ½ 6 r e k a e p s d u o L8 6 0 0 0 0 2 6
1 2½ 4 V 0 3 2 n a F5 1 0 0 0 0 7 6 
						

							Page 39
m e t Ino i t p i r c s e DoN t r a P
12r e V l a c e D l e n a P y a l P73 4 0 0 0 0 4
2mr o F - c a V l e n a P y a l P69 1 0 0 0 6 4
3de R B P C M - y s s A n o t t u b h s u P74 2 0 0 2 0 6
4wo l l e Y B P C M - y s s A n o t t u b h s u P15 2 0 0 2 0 6
5hs e M r e k a e p s d u o L l e n a P y a l P59 1 0 0 0 6 4
6do o W g n i t n u o M r e k a e p S / l e n a P y a l P31 1 0 0 1 7 3
7hg i H d i M  ½ 5 r e k a e p s d u o L56 0 0 0 0 2 6
2
43
56
7 1 
						

							Page 40
1
6
5
2
34
m e t Ino i t p i r c s e DoN t r a P
1k c a l B - d a e H n a P z P 0 2 x 4 M1 9 3 0 0 3 6 2
k c a l B - r e h s a W t a l F 4 M2 3 1 0 0 0 8 2
2re h s a W p i r G e l o P i k S6 0 6 0 0 0 5 4
3ra B p i r G e l o P i k S9 3 2 0 0 0 6 4
4SH L - g n i t s a C t n i o J e l o P i k S9 0 2 0 0 0 6 4
5SH R - g n i t s a C t n i o J e l o P i k S0 1 2 0 0 0 6 4
6en i L m i l S k c a l B - p i r G e l o P i k S5 4 2 0 0 0 6 4 
						

							Page 41
1
2
3
45
6
7
8
9 10
11
12
13
14