Multitech Multivoip 100 Model Mvp110 Standalone Voice/ip Gateway Quick Start Guide

21 Configure Host MultiVOIP
28. Click OK and you are returned to the Phone Directory
Database dialog box, which now includes phone number
101 with its IP address, channel number, and description.
29. Click Add and the Add/Edit Phone Entry dialog box
displays again.
30. Enter the phone number for the remote MultiVOIP in the
Station Information group Phone Number box.  For
example, 201.
31. Enter a description for the remote MultiVOIP phone
number in the Description box.
Note: If the remote MultiVOIP is...

MultiVOIP Quick Start Guide
2232. Enter the IP address of the remote MultiVOIP in the IP
Address box in the MultiVOIP Identification group.
33. Click OK and you are returned to the Phone Directory
Database dialog box, which now includes the second
number and related information in the Phone Number
list.
34. When you have finished, click OK.  On the Main menu,
click Download Setup.     

23 Configure Host MultiVOIP
35. The Save Setup dialog box displays.
Click OK to proceed.
36. After the setup is written to the MultiVOIP, the unit is
rebooted.
37. Verify that the BOOT LED on the MultiVOIP is off after the
download is complete.  This may take several minutes as
the MultiVOIP reboots.
38.Win3.1 users - you are returned to your Program
Manager where the MultiVOIP Program Group and
Program Items (Windows icons) display.
Win95/98/NT/2000 users - you are returned to your
MultiVOIP folder...

MultiVOIP Quick Start Guide
24
Configuring Your ClientMultiVOIPs
If you are installing a MultiVOIP behind a firewall, you need to
add the following UDP ports to your firewall.
900 Signaling Information 5004 RTP Packets
5000 Status Information 5005 RTCP Packets
Refer to your firewall user documentation to enter and open
these ports.
1. Disconnect the PC from the command port of the Host
MultiVOIP and connect it to the command port on the
Client MultiVOIP.
2.Win 3.1 users - from the Program Manager,...

25 Configure Client MultiVOIPs
match your IP network, select the Frame Type from the
Frame Type list.  The Frame Type choices are TYPE_II
and SNAP.
4. In the Port Address group, enter the IP Address and IP
Mask.  In the Gateway Address group, enter the gateway
IP address for the client unit.
The IP address is your unique LAN IP address, and the
Gateway address is the IP address of the device
connected to the Internet/Intranet.
Click OK when you are finished.  The Channel Setup
dialog box displays.
5. The...

MultiVOIP Quick Start Guide
26Check with your in-house telephone personnel to verify
whether your local PBX dial signaling is Pulse or DTMF
(tone).  Set the Regeneration option accordingly.  In the
Max Dial Digits box, enter the maximum number of digits
allowed when dialing a phone number.  The default setting
is 5.  In the Inter Digit Time box, enter the maximum
amount of time in milliseconds that the unit will wait before
mapping the dialed digits to an entry in the Phone
Directory Database.  If too...

27 Configure Client MultiVOIPs
If you changed the voice coder, ensure that the same
voice coder is used on the voice/fax channel you are
calling.  Otherwise, you will always get a busy signal.
9. The Fax group enables you to select the maximum baud
rate for faxes and adjust the fax volume.  If you do not plan
to send or receive faxes on a given voice/fax channel, you
can disable faxes in the Fax group.
10. The Billing/Security tab displays the parameters for
billing options, call authentication, and...

MultiVOIP Quick Start Guide
2813. The Automatic Disconnect option limits call duration to
the number of seconds entered in the Disconnect After
box.  The default value of 180 seconds can be changed
to any other value up to 65,535 (roughly 18.2 hours).
14. To change the Tone Pairs on the Regional tab, select
your specific country or region from the Country/Region
list.
The Tone Pairs group parameters change per your
selections. Click OK.  The following dialog box displays.
 
15. Click OK after the upgrade...

29 Configure Client MultiVOIPs
main menu, click Phone Book to display the Phone
Directory Database dialog box.
In the Database Type group, click the Client option.  The
Host IP Address box becomes active.
16. Enter the IP address of the host MultiVOIP in the Host IP
Address box.
17. Click OK and you are returned to the main menu.
18. Click Download Setup to write the new configuration to
the client unit.  The Save Setup dialog box displays.
19. Select the Save Current Setup as User Default
Configuration...

MultiVOIP Quick Start Guide
3020. Verify that the Boot LED on the MultiVOIP is off after the
download is complete.  This may take several minutes as
the MultiVOIP reboots.
21. You are returned to the main menu.
Your MultiVOIP is operational at this time.
Repeat this procedure for each of the client units.  When all
clients have been configured, proceed with deploying the
VOIP network.