Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways User Guide

MultiVOIP User Guide Operation and Maintenance
361
4. The  MVP____- Firmware  screen appears saying “MultiVOIP [model
number] is up.  Reboot to Download Firmware?”
Click OK to download the factory defaults.
The “Boot” LED on the MultiVOIP will light up and remain lit during
the file transfer process.
5. After the PC gets a response from the MultiVOIP, the Dialog – IP
Parameters screen will appear.
The user should verify that the correct IP parameter values are listed
on the screen and revise them if...

Operation and Maintenance MultiVOIP User Guide
362
Setting and Downloading User Defaults
The Download User Defaults commandallows you to maintain a known
working configuration that is specific to your VOIP system.  You can then
experiment with alterations or improvements to the configurations confident
that a working configuration can be restored if necessary.
1. Before you can invoke the Download User Defaults command, you
must first save a set of configuration parameters by using the Save
Setup command...

MultiVOIP User Guide Operation and Maintenance
363
4. Progress bars will appear during the  file transfer process.
5. When the file transfer process is complete, the Dialog-- IP
Parameters screen will appear.
6. Set the IP values per your particular VOIP system.  Click OK.
Progress bars will appear as the MultiVOIP reboots itself. 

Operation and Maintenance MultiVOIP User Guide
364
Setting a Password (Windows GUI)
After a user name has been designated and a password has been set,
that password is required to gain access to any functionality of the
MultiVOIP software. Only one user name and password can be
assigned to a voip unit.  The user name will be required when
communicating with the MultiVOIP via the web browser GUI.
NOTE:  Record your user name and password in a safe place. If
the password is lost, forgotten, or...

MultiVOIP User Guide Operation and Maintenance
365
4. The Password screen will appear.  If you intend to use the FTP Server
function that is built into the MultiVOIP, enter a user name. (A User
Name is not needed to access the local Windows GUI, the web
browser GUI, or the commands in the Program group.) Type your
password in the Password field of the Password screen.  Type this
same password again in the Confirm Password field to verify the
password you have chosen.
NOTE:  Be sure to write down your...

Operation and Maintenance MultiVOIP User Guide
366
6. After the password has been set, the user will be required to enter the
password to gain access to the web browser GUI and any part of the
MultiVOIP software listed in the Program group menu.  User Name
and Password are both needed for access to the FTP Server residing in
the MultiVOIP.
When MultiVOIP program asks for password at launch of program, the
program will simply shut down if CANCEL is selected.
The MultiVOIP program will produce an error...

MultiVOIP User Guide Operation and Maintenance
367
Setting a Password (Web Browser GUI)
Setting a password is optional when using the MultiVOIP web browser
GUI.  Only one password can be assigned and it works for all
MultiVOIP software functions (Windows GUI, web browser GUI, FTP
server, and all Program menu commands, e.g., Upgrade Software –
only the FTP Server function requires a User Name in addition to the
password). After a password has been set, that password is required to
access the MultiVOIP web...

Operation and Maintenance MultiVOIP User Guide
368
Un-Installing the MultiVOIP Software
1. To un-install the MultiVOIP configuration software, go to Start |
Programs and locate the MultiVOIP entry.  Select Uninstall MVP____
vx.xx (versions may vary).
2. Two confirmation screens will appear.  Click Yes and OK when you
are certain you want to continue with the uninstallation process. 

MultiVOIP User Guide Operation and Maintenance
369
3. A special warning message similar to that shown below may appear
for the MultiVOIP software’s “.bin” file.  Click Yes.
5 2%&8% %9% &2%2%:
%9% &2%2%:95 &62:
	$1# %1
1!; 1!9) %&)
#&& %2%2%
3 :(

Operation and Maintenance MultiVOIP User Guide
370
Upgrading Software
As noted earlier (see the section Implementing a Software Upgrade above),
the Upgrade Software command transfers, from the controller PC to the
MultiVOIP unit, firmware (including the H323 stack) and factory
default configuration settings.  As such, Upgrade Software implements
the functions of both Download Firmware and Download Factory
Defaults in a single command.