Home
>
Multi-Tech Systems
>
Communications System
>
Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide
Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide
Here you can view all the pages of manual Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide. The Multi-Tech Systems manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 81
MultiVOIP User Guide Software Installation 81 8. A completion screen will appear. Click Finish. 9. When setup of the MultiVOIP software is complete, you will be prompted to run the MultiVOIP software to configure the VOIP. Software installation is complete at this point. You may proceed with Technical Configuration now or not, at your convenience. Technical Configuration instructions are in the next two chapters of this manual: Chapter 5 for T1/E1 MultiVOIP units and Chapter 6 for Analog MultiVOIP units.
Page 82
Software Installation MultiVOIP User Guide 82 Un-Installing the MultiVOIP Configuration Software 1. To un-install the MultiVOIP configuration software, go to Start | Programs and locate the entry for the MultiVOIP program. Select Uninstall.
Page 83
MultiVOIP User Guide Software Installation 83 2. Two confirmation screens will appear. Click Yes and OK when you are certain you want to continue with the uninstallation process. 3. A special warning message similar to that shown below may appear concerning the MultiVOIP software’s “.bin” file. Click Yes.
Page 84
Software Installation MultiVOIP User Guide 84 4. A completion screen will appear. Click Finish.
Page 86
86 Chapter 5: Technical Configuration for Digital T1/E1 MultiVOIPs (MVP2400, MVP2410, MVP3010)
Page 87
MultiVOIP User Guide Technical Configuration (Digital Voips) 87 Configuring the Digital T1/E1 MultiVOIP There are two ways in which the MultiVOIP must be configured before operation: technical configuration and phonebook configuration. Technical Configuration. First, the MultiVOIP must be configured to operate with technical parameter settings that will match the equipment with which it interfaces. There are seven types of technical parameters that must be set. These technical parameters pertain to...
Page 88
MultiVOIP User Guide Technical Configuration (Digital Voips) 88 Remote configuration is done through a connection between the MultiVOIP’s Ethernet (network) port and a computer connected to the same network. The computer could be miles or continents away from the MultiVOIP itself. There are two ways of doing remote configuration and operation of the MultiVOIP unit: (1) using the MultiVoipManager SNMP program, or (2) using the MultiVOIP web browser interface program. MultiVoipManager. MultiVoipManager...
Page 89
MultiVOIP User Guide Technical Configuration (Digital) 89 Local Configuration This manual describes local configuration only. For information on remote configuration and management, see the MultiVoipManager documentation. Pre-Requisites To complete the configuration of the MultiVOIP unit, you must know several things about the overall system. Before configuring your MultiVOIP Gateway unit, you must know the values for several IP and T1/E1 parameters that describe the IP network system and telephony...
Page 90
MultiVOIP User Guide Technical Configuration (Digital Voips) 90 T1 Telephony Parameters (for MVP2400 & MVP2410) The following parameters must be known about the PBX or telco central office equipment to which the T1 MultiVOIP will connect: ➼ T1 Phone Parameters Ask phone company or PBX maintainer. Info needed to operate: MVP2400 MVP2410 T1 Telephony Parameters: Record for this VOIP Site • Which frame format is used? ESF___ or D4___ • Which CAS or PRI protocol is used? ______________ • Clocking: Does...