Home
>
Multi-Tech Systems
>
Communications System
>
Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide
Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide
Here you can view all the pages of manual Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways S000249C User Guide. The Multi-Tech Systems manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 61
MultiVOIP User Guide Mechanical Installation & Cabling 61 Unpacking Your MultiVOIP When unpacking your MultiVOIP, check to see that all of the items shown are included in the box. For the various MultiVOIP models, the contents of the box will be different. Study the particular illustration below that is appropriate to the model you have purchased. If any box contents are missing, contact MultiTech Tech Support at 1-800-972-2439. Unpacking the MVP2410/3010 Figure 3-1: Unpacking the MVP2410/3010
Page 62
Mechanical Installation & Cabling MultiVOIP User Guide 62 Unpacking the MVP2400 Voic e/Fax over IP Networks200 Quick Start Guide Figure 3-2: Unpacking the MVP2400
Page 63
MultiVOIP User Guide Mechanical Installation & Cabling 63 Unpacking the MVP410/810 Voice/Fax over IP Networks RCV XMT CO L LNKX M T R C V XS G R SG XMT RCV XSG RSG XMT RCV XSG RSG XMT RC V XSG RSG XMT RC V XSG RSGXMT RCV XSG RSG XMT RCV XSG RSG Vo ic e/Fax 5 Voice /Fax 6 Voic e/ Fax 7 Voic e/Fax 8 Voi ce/ F ax 1 Vo ic e/Fax 2 Voic e/ Fax 3Voi c e/F ax 4 Ether net BootPowerXMT RCV XSG RSG Quick Start Guide Figure 3-3: Unpacking the MVP410/810
Page 64
Mechanical Installation & Cabling MultiVOIP User Guide 64 Unpacking the MVP210 Voic e/Fax over IP Networks200 Quick Start Guide Figure 3-4: Unpacking the MVP210
Page 65
MultiVOIP User Guide Mechanical Installation & Cabling 65 Rack Mounting Instructions for MVP2410/3010 & MVP410/810 The MultiVOIPs can be mounted in an industry-standard EIA 19-inch rack enclosure, as shown in Figure 2-5. Figure 3-5: Rack-Mounting (MVP2410/3010 or MVP410/810)
Page 66
Mechanical Installation & Cabling MultiVOIP User Guide 66 Safety Recommendations for Rack Installations Ensure proper installation of the unit in a closed or multi-unit enclosure by following the recommended installation as defined by the enclosure manufacturer. Do not place the unit directly on top of other equipment or place other equipment directly on top of the unit. If installing the unit in a closed or multi-unit enclosure, ensure adequate airflow within the rack so that the maximum recommended...
Page 67
MultiVOIP User Guide Mechanical Installation & Cabling 67 19-Inch Rack Enclosure Mounting Procedure Attaching the MultiVOIP to a rack-rail of an EIA 19-inch rack enclosure will certainly require two persons. Essentially, the technicians must attach the brackets to the MultiVOIP chassis with the screws provided, as shown in Figure 3-6, and then secure unit to rack rails by the brackets, as shown in Figure 3-7. Because equipment racks vary, screw for rack-rail mounting are not provided. Follow the...
Page 68
Mechanical Installation & Cabling MultiVOIP User Guide 68 Cabling Cabling Procedure for MVP2410/3010 Cabling your MultiVOIP entails making the proper connections for power, command port, phone system (T1/E1 line connected to PBX or telco office), and Ethernet network. Figure 3-8 shows the back panel connectors and the associated cable connections. The following procedure details the steps necessary for cabling your MultiVOIP. 1. Connect the power cord to a live AC outlet, then connect it to the...
Page 69
MultiVOIP User Guide Mechanical Installation & Cabling 69 3. Connect a network cable to the Ethernet connector on the back of the MultiVOIP. Connect the other end of the cable to your network. 4. Turn on power to the MultiVOIP by setting the power switch on the right side panel to the ON position. Wait for the Boot LED on the MultiVOIP to go off before proceeding. This may take a couple of minutes. Proceed to Chapter 4 “Software Installation.” Cabling Procedure for MVP2400 Cabling your MultiVOIP...
Page 70
Mechanical Installation & Cabling MultiVOIP User Guide 70 3. Connect a network cable to the Ethernet connector on the back of the MultiVOIP. Connect the other end of the cable to your network. 4. Turn on power to the MultiVOIP by setting the power switch on the right side panel to the ON position. Wait for the Boot LED on the MultiVOIP to go off before proceeding. This may take a couple of minutes. Proceed to Chapter 4 “Software Installation.” Cabling Procedure for MVP410/810 Cabling involves...