Home
>
Multi-Tech Systems
>
Communications System
>
Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways Quick Start Guide
Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways Quick Start Guide
Here you can view all the pages of manual Multi-Tech Systems Mvp-2400/2410/3010, Mvp-210/410/810 Voice/ip Gateways Quick Start Guide. The Multi-Tech Systems manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 1
Voice / Fax over IP Networks Quick Start Guide for Voice/IP Gateways Digital Models (T1, E1, ISDN-PRI): MVP-2400/2410/3010 Analog Models: MVP-210/410/810
Page 2
2 Quick Start Guide 82000250, Revision A Analog MultiVOIP Units (Models MVP210, MVP410, and MVP810) Digital MultiVOIP Units (Models MVP2400, MVP2410, MVP3010,) This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2002, by Multi-Tech Systems, Inc. Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied...
Page 3
3 CONTENTS Introduction 4 Safety Warnings 4 Lithium Battery Caution 4 Safety Warnings Telecom 4 MultiVOIP Startup Tasks 5 Phone/IP Details *Absolutely Needed* Before Starting the Installation 6 Gather IP Information 6 Gather Telephone Information 6 Gather Telephone Information 7 Gather Telephone Information 7 Obtain Email Address for VOIP (for email call log reporting) 8 Identify Remote VOIP Site to Call 8 Idenitfy VOIP Protocol to be Used 8 Placement 9 The Command/Control Computer (Specs...
Page 4
Safety Warnings MultiVOIP Quick Start Guide 4 Introduction This manual will get your MultiVOIP up and running quickly. For more details, see the MultiVOIP User Guide. Safety Warnings Lithium Battery Caution A lithium battery on the voice/fax channel board provides backup power for the timekeeping capability. The battery has an estimated life expectancy of ten years. When the battery starts to weaken, the date and time may be incorrect. If the battery fails, the board must be sent back to Multi-Tech...
Page 5
MultiVOIP Quick Start Guide Startup Tasks 5 MultiVOIP Startup Tasks TaskSummary Collecting Phone/IP Details (vital!) The MultiVOIP must be configured to interface with your particular phone system and IP network. To do so, certain details must be known about those phone and IP systems. PlacementDecide where you’ll mount the voip. The Command/Control Computer: Specs & Settings Some modest minimum specifications must be met. A COM port must be set up. HookupConnect power,...
Page 6
Gathering Phone/IP Details MultiVOIP Quick Start Guide 6 Phone/IP Details *Absolutely Needed* Before Starting the Installation The MultiVOIP will interface with both the IP network and the phone system. You must gather information about the IP network and about the phone system so that the MultiVOIP can be configured to operate with them properly. Gather IP Information ➼Ask your computer network administrator.Info needed to operate: all MultiVOIP models. IP Network Parameters: Record for each VOIP Site...
Page 7
MultiVOIP Quick Start Guide Gathering Phone/IP Details 7 Phone/IP Details *Absolutely Needed* Gather Telephone Information ➼E1 Phone Parameters Ask phone company or PBX maintainer. Info needed to operate: MVP3010 E1 Telephony Parameters: Record for this VOIP Site • Which frame format is used? Double Frame_____ MultiFrame w/ CRC4_____ MultiFrame w/ CRC4 modified_____ • Which CAS or PRI protocol is used? ______________ • Clocking: Does the PBX or telco switch use internal or external clocking?...
Page 8
Gathering Phone/IP Details MultiVOIP Quick Start Guide 8 Phone/IP Details Often Needed/Wanted Obtain Email Address for VOIP (for email call log reporting) required if log reports of VOIP call traffic are to be sent by email Optional SMTP Parameters Preparation Task: Ask Mail Server administrator to set up email account (with password) for the MultiVOIP unit itself. Be sure to give a unique identifier to each individual MultiVOIP unit. Get the IP address of the mail server computer, as well.To: I . T....
Page 9
MultiVOIP Quick Start Guide Voip Placement & PC Settings 9 Placement Mount your MultiVOIP in a safe and convenient location where cables for your network and phone system are accessible. Rack-mounting instructions are in Chapter 3: Mechanical Installation & Cabling of the User Guide. The Command/Control Computer (Specs & Settings) The computer used for command and control of the MultiVOIP (a) must be an IBM-compatible PC, (b) must use a Microsoft operating system, (c) must be connected to your local...