Multi-Tech Systems MultiVOIP Model Mvp400/800 Standalone Voice/ip Gateway User Guide

31 Chapter 3 - Software Loading and Configuration
Phase 2: Configure Your Slave MultiVOIPs
The slave MultiVOIPs can be another MVP 400 or MVP 800 unit or a MultiVOIP-series.
If your slave MultiVOIP is an MVP 400 or MVP 800, perform the following software loading
procedure.
If your slave is a MultiVOIP-series, connect your command port cable and power up the unit
according to the cabling procedure in the MultiVOIP-series Quick Start.  Then configure the unit as a
slave per the Installing Your MultiVOIP...

32 MultiVOIP User Guide
3 The IP Setup dialog box is displayed.
The default Frame Type is TYPE_II. If this does not match your IP network, change the Frame
Type by clicking on the drop down box. The Frame Type choices are TYPE_II and SNAP.
4 In the Port Address group, enter the IP Address and IP Mask. In the Gateway Address
group, enter the gateway IP address for the slave unit.
The IP address is your unique LAN IP address, and the Gateway address is the IP address of
the device connected to the...

33 Chapter 3 - Software Loading and Configuration
If you are using an extension from your PBX, then chose FXO option.  Check with your in-
house telephone personnel to verify connection type.
If you chose an FXO interface, then the Dialing Options Regeneration group is enabled.
Check with your local in-house telephone personnel to verify whether your local PBX dial
signaling is Pulse or tone (DTMF). Set the Regeneration option accordingly.
If you are connecting to a E&M trunk on your PBX, then chose E&M...

34 MultiVOIP User Guide
9 To change the voice coder, first select the channel by clicking the Select Channel down
arrow and highlighting the channel number, then click the Voice Coder down arrow and
highlight your new voice coder entry.
If you changed the voice coder, ensure that the same voice coder is used on the voice/fax
channel you are calling; otherwise, you will always get a busy signal.
10 If you selected the FXO interface and are using touchtone dialing, you can set up the DTMF
gain (or output...

35 Chapter 3 - Software Loading and Configuration
15 To change the Tone Pairs on the Regional tab, click the Country/Region down arrow and
highlight your specific country or region.
The Tone Pairs group parameters change per your choice.  Click OK and you are returned to
the main menu.
16 From the main menu, click Phone Book to display the Phone Directory Database dialog box.
In the Database Type group, click the Slave option.  The Master IP Address field becomes
active.
17 Enter the IP address of the...

36 MultiVOIP User Guide
20 Select (check) Save Current Setup as the User Default Configuration, then click OK.
21 The Writing Setup dialog box is displayed as the setup configuration is written to the
MultVOIP.
After the setup is written to the MultiVOIP, the unit reboots.
22 Check that the BTG LED on the MultiVOIP is Off after the download is complete. This may
take several minutes as the MultiVOIP reboots.
23 You are returned to the main menu.
Your MultiVOIP is operational at this time.         

37 Chapter 3 - Software Loading and Configuration
Phase 3:  Deploy the VOIP Network
Phase 3 involves the VOIP Administrator developing the VOIP Dialing Directory and deploying the
preconfigured slave MultiVOIPs to their remote sites.  The remote site administrators need only
connect power to the preconfigured MultiVOIP, connect it to their Ethernet LAN and predefined
telephone equipment, and then wait for the phone directory database to be down loaded.
The slave units can be another MVP 400 or MVP 800...

38 MultiVOIP User Guide
If you are connecting the station side of a telephone switch (PBX) to your MultiVOIP, connect
one end of an RJ11 phone cord to the Voice/Fax Channel 1 FXO connector on the back of
the MultiVOIP and the other end to the phone jack.
If you are connecting an E&M trunk from a telephone switch to your MultiVOIP, connect one
end of an RJ45 phone cord to the Voice/Fax Channel 1 E&M connector on the back of the
MultiVOIP and the other end to the trunk. Refer to Appendix B for E&M cabling...

Chapter 4 - MultiVOIP Software 

40 MultiVOIP User Guide
Introduction
This chapter describes the MultiVOIP software with the intent to show you how to make changes to
the configuration of your MultiVOIP. The major configuration parameters were established during the
loading of the software (Chapter 3), and the MultiVOIP software and configuration utilities allow you
to make changes to that initial configuration.
The MultiVOIP software allows you to refine your configuration based on your network connections.
The software is based on a...