MSI Hetis 865gv-e Manual

Chapter 2
2-14IEEE 1394 Port: J1394-1
The bigger 6-pin IEEE 1394 Port on the back panel is designed for you to
connect IEEE 1394 devices without external power.  That means the mainboard
can provide the power for the devices connected to this port.
VGA  Port
The mainboard provides one DB 15-pin female connector to connect a
VGA monitor. Software Support
IEEE 1394 Driver is provided by Windows®
 98 SE,   Windows®
  XP,
Windows®
 ME and Windows®
 2000.  Just plug in the IEEE 1394
connector into the port....

Introducing Mainboard
2-15 The mainboard offers two 9-pin male DIN connectors as serial ports.  The
ports are 16550A high speed communication ports that send/receive 16 bytes
FIFOs.  You can attach a serial mouse or other serial devices directly to the
connector. Serial Port
PIN     SIGNALDESCRIPTION
1          DCDData Carry Detect
2          SINSerial In or Receive Data
3          SOUTSerial Out or Transmit Data
4          DTRData Terminal Ready
5          GNDGround
6          DSRData Set Ready
7...

Chapter 2
2-16 .
IDE Connector: IDE1
The mainboard has a 32-bit Enhanced PCI IDE and Ultra DMA 33/66/100
controller that provides PIO mode 0~4, Bus Master, and Ultra DMA/33/66/100
function.  The connector on the mainboard allows you to connect to the IDE
devices: HDD & CD-ROM. 2.7 ConnectorsSerial ATA Connectors:  SATA1, SATA2
The southbridge of this mainboard is ICH5 which supports two serial
connectors SATA1& SATA2.
SATA1 & SATA2 are dual high-speed Serial ATA interface ports. Each
supports 1st...

Introducing Mainboard
2-17 CD-in Connector: JCD1
The connector is for CD-ROM audio connector. PINSIGNALDESCRIPTION
1HD_LED_PHard disk LED pull-up
2FP PWR/SLPMSG LED pull-up
3HD_LED_NHard disk active LED
4FP PWR/SLPMSG LED pull-up
5RST_SW_NReset Switch low reference pull-down to GND
6PWR_SW_PPower Switch high reference pull-up
7RST_SW_PReset Switch high reference pull-up
8PWR_SW_NPower Switch low reference pull-down to GND
9RSVD_DNUReserved. Do not use.  JFP1 Pin DefinitionFront Panel Connector: JFP1
The...

Chapter 2
2-18 Internal Speaker Connector: CON1
This connector is used to connect the built-in speaker. The CPUFAN1 (CPU fan) and SYS_FAN1 (system fan) support system
cooling fans with +12V that is controlled by PWM.
When connecting the wire to the three-pin head connectors, always note
that the red wire is the positive and should be connected to the +12V (that is
controlled by PWM), the black wire is Ground and should be connected to
GND.  If the mainboard has a System Hardware Monitor chipset on-board,...

Introducing Mainboard
2-19 Front USB Connector: J3
The mainboard provides one standard USB 2.0 pin header J3 to
connect to a card reader. USB 2.0 technology increases data transfer rate up
to a maximum throughput of  480Mbps, which is 40 times faster than USB 1.1.
PINSIGNALPINSIGNAL
1VCC2VCC
3USB0-4USB1-
5USB0+6USB1+
7GND8GND
9Key (no pin)10USBOCJ3 Pin Definition
J3      1    2
  10    9Note that the pins of VCC and GND must be connected correctly or
it may cause some damage. 

Chapter 2
2-20 The motherboard provides one jumper for you to set the computer’s
function. This section will explain how to change your motherboard’s function
through the use of the jumper.
Clear CMOS Jumper: JBAT1
There is a CMOS RAM on board that has a power supply from external
battery to keep the system configuration data. With the CMOS RAM, the
system can automatically boot OS every time it is turned on. That battery has
long life time for at least 5 years.  If you want to clear the system...

Introducing Mainboard
2-21  Order 1 Order 2 Order 3 Order 4 1394 INT D#    PCI Slot INT B# INT C# INT D# INT A#  PCI  Interrupt Request Routing
The IRQ, abbreviation of interrupt request line and pronounced I-R-Q,
are hardware lines over which devices can send interrupt signals to the
microprocessor.  The “AGP/PCI” IRQ pins are typically connected to the PCI
bus INT A# ~ INT D# pins as follows: The mainboard provides one 32-bit Master PCI bus slot.
The PCI slot allows you to insert PCI Riser Card.  The...

System Assembly
3-1This chapter provides you with the installation procedures of
Hetis barebone. It is useful for you to read the information of
mainboard setup before assembling the whole system.3 System Assembly 

Chapter 3
3-2 The built-in MS-7065 mainboard is designed for Hetis barebone only.
Except MS-7065 mainboard, the built-in components of the barebone include
power supply and PCI riser card.  In this chapter we’ll show you how to install
CPU,  FDD, HDD, CD-ROM and CPU Cooler.
Installation ToolsScrews
Four types of screws are used in assembling the barebone:  round-
headed screw, hexagonal screw with washer, thumb screw and flat-
headed screw.
Round-headed screw: This type of screw is used to attach
the HDD...