MSI 865pe Neo2 V Manual

3-26
MS-6728 ATX Mainboard
Serial Port B Mode
This item sets the operation mode for Serial Port B. Settings: Normal,
1.6uS, 3/16 Baud and ASKIR (the last three operation modes are
settingoptions for IR function).
IR Duplex Mode
This setting controls the operating mode of IR transmission/
reception. Setting options: Full Duplex, Half Duplex. Under Full
Duplex mode, synchronous, bi-directional transmission/reception
is allowed. Under Half Duplex mode, only asynchronous, bi-
directional...

3-27
BIOS Setup
PC Health Status
This section shows the status of your CPU, fan, overall system status,
etc.  Monitor function is available only if there is hardware monitoring mecha-
nism onboard.
Chassis Intrusion
The field enables or disables the feature of recording the chassis intrusion
status and issuing a warning message if the chassis is once opened.  To clear
the warning message, set the field to Reset.  The setting of the field will
automatically return to Enabled later.  Settings: Enabled,...

3-28
MS-6728 ATX Mainboard
Use this menu to specify your settings for frequency/voltage control.
CPU Ratio Selection
This setting controls the multiplier that is used to determine the internal clock
speed of the processor relative to the external or motherboard clock speed.
DRAM  Frequency
Use this field to configure the clock frequency of the installed DRAM. Settings
are: PSB 400:  266, Auto.
 PSB 533:  266, 333, Auto, 354.
 PSB 800:  266, 333, 400, Auto, 500, 532.
Spread Spectrum
When the motherboard’s...

3-29
BIOS Setup
Adjust CPU Bus Clock
This item allows you to select the CPU Bus clock frequency (in MHz) and
overclock the processor by adjusting the FSB clock to a higher frequency.
DDR Clock (Mhz)
This item allows you to view the current DDR clock.
Adjust AGP/PCI Clock (Mhz)
This item allows you to select the AGP/PCI clock frequency (in MHz) by
adjusting the AGP/PCI clock to a higher frequency.
CPU Vcore Adjust
The setting allows you to adjust the CPU Vcore voltage. Available options:
Yes, No.
CPU...

3-30
MS-6728 ATX Mainboard
Set Supervisor/User Password
When you select this function, a message as below will appear on the
screen:
Type the password, up to six characters in length, and press .
The password typed now will replace any previously set password from CMOS
memory. You will be prompted to confirm the password. Retype the password
and press . You may also press  to abort the selection and not
enter a password.
To clear a set password, just press  when you are prompted to
enter the password. A...

3-31
BIOS Setup
Load High Performance/BIOS Setup Defaults
The two options on the main menu allow users to restore all of the BIOS
settings to High Performance defaults or BIOS Setup defaults. The High
Performance Defaults are the values set by the mainboard manufacturer for the
best system performance but probably will cause a stability issue. The BIOS
Setup Defaults are the default values also set by the mainboard manufacturer
for stable performance of the mainboard.
When you select Load High...

Using 2-, 4- or 6-Channel Audio Function
A-1
Appendix. Using 4- or 6-Channel
Audio FunctionAppendix A: Using 2-, 4- or 6-Channel
Audio Function
The motherboard comes with C-Media 9739A AC’97 audio chip, which
provides exclusive Xear 3DTM technology, a value-add PC audio total solution.
In addtion, C-Media designs a Universal Driver Architecture (UDA driver)
which has a flexible interface so that it can be applied to different platforms and
all C-Media audio chips. C-Media  9739A allows the board to...

A-2
MS-6728 ATX Mainboard
The mainboard is able to transform the audio connectors on the back panel
from 2-channel to 4-/6-channel.  To use the function, you need to install the C-
Media UDA driver.
The UDA driver supports all Windows, C-Midia AC’97 CODEC, and audio
controllers (south bridges) on board. Moreover, there is no operation barrier
when switching to other C-Media’s products.
Main Features of UDA Driver V.029:
1.Xear 3D - 5.1 Virtual SPEAKER SHIFTER:
h It allows users to enjoy multi-channel...

Using 2-, 4- or 6-Channel Audio Function
A-3
settings.
6.Demo Program - Play3D Demo: It provides 5 sound sources and moving
path for playing for 3D audio playing. You can feel 3D positional sound and
also use this program to adjust your virtual speakers before playing 3D
audio applications like gaming.
7.Demo Program - Multi-channel Music: Multi-channel Music Demo
Program has three 5.1-channel melodies for playing. You can also click on
the speakers respectively to test each channel and adjust virtual...

A-4
MS-6728 ATX Mainboard
After installing the audio driver, you are able to use the 4-/6-channel
audio feature now.  To enable 4- or 6-channel audio operation, first connect 4 or
6 speakers to the appropriate audio connectors, and then select 4- or 6-channel
audio setting in the software utility.
There are two ways to utilize the function and connect the speakers to
your computer:
„Use the optional S-Bracket.  If your motherboard supports S-Bracket
and you have installed S-Bracket in the computer, you...