Motorola Sse 5000 6881094c12 A Manual

Chapter 6 Encryption
This chapter describes the encryption capability of the SSE 5000 radio.
6.1 Load an Encryption Key
To load an encryption key:
1. Refer to the key-variable loader (KVL) manual for equipment connections and setup.
2. Attach the KVL to the radio. The display shows “KEYLOAD.” All other radio functions, except 
for power down, backlight, and volume, are locked out.
3. Refer to the KVL manual for how to load the encryption keys into the radio.
4. When the key is loaded successfully, you...

November 11, 20046881094C12-A
6-2Encryption: Multikey Feature
Notes 

Chapter 7 Disassembly/Reassembly Procedures
This chapter provides detailed procedures for disassembling/reassembling SSE 5000 radios and 
also includes preventive maintenance and handling precautions, which provide information vital to 
the successful operation and maintenance of your radio.
When performing the disassembly/reassembly procedures, refer to the exploded view (Figure 7-1 on 
page 7-3) and to the parts list (Table 7-1 on page 7-4). Items in parentheses ( ) throughout this 
chapter refer to...

November 11, 20046881094C12-A
7-2Disassembly/Reassembly Procedures: Handling Precautions
7.2 Handling Precautions
Complementary metal-oxide semiconductor (CMOS) devices, and other high-technology devices, 
are used in this family of radios. While the attributes of these devices are many, their characteristics 
make them susceptible to damage by electrostatic discharge (ESD) or high-voltage charges. 
Damage can be latent, resulting in failures occurring weeks or months later. Therefore, special...

6881094C12-ANovember 11, 2004
Disassembly/Reassembly Procedures: SSE 5000 Exploded View 7-3
7.3 SSE 5000 Exploded View
This section contains the SSE 5000 radio exploded view and parts list.
NOTES:
• Numbers in parentheses ( ) refer to item numbers in Figure 7-1 and Table 7-1 on page 7-4.
Figure 7-1.  SSE 5000 Exploded View
53
4743
62
49
67
64
60
56
5051
61
65
34
44
46
48
45
27
2635
10
16
66
23
31
21
39
25
41
42
4
7
3
1
12
11
5
6
59
68
17
2
8
9
19
1419
29
37
33
30
2522
63
40
132438
14
36
18
20
15
32
28...

November 11, 20046881094C12-A
7-4Disassembly/Reassembly Procedures: SSE 5000 Exploded View
Table 7-1.  SSE 5000 Exploded View Parts List
ItemPart NumberDescriptionQty
1NNTN4467_ KIT, HOUSING (includes items 2–12)1
2   6485388E02    ASSEMBLY, BASEPLATE 1
3   3205472M02    SEAL, PORT 1
4   5585389E01    LATCH, BATTERY  1
5   0305731J22    SCREWS, CONTACT 3
6   3905253X01    CONTACTS, POWER  3
7   4105775Q01    LATCH, SPRING  1
8   1485390E01    INSULATOR, BASEPLATE CONTACT  1
9   3285391E01    SEAL,...

6881094C12-ANovember 11, 2004
Disassembly/Reassembly Procedures: SSE 5000 Exploded View 7-5
38
   4385294E01    BUSHING, ANTENNA/INSULATOR 1
39   6185418E01    LIGHTPIPE, TX       1
40   6485298E02    SUB-ASSEMBLY, CONTROL TOP  1
41   7285419E01    MODULE, LCD                    1
42   7585729E01    PAD, DUST, DISPLAY  1
43   8485687E01    ASSEMBLY, CONTROL FLEX (includes items 44–49)1
44      1885300E01        SWITCH, VOLUME POT 1
45      4005572W04       SWITCH, 3-POSITION TOGGLE 1
46      4085299E01...

November 11, 20046881094C12-A
7-6Disassembly/Reassembly Procedures: Disassembly/Reassembly Procedures for Accessories
7.4 Disassembly/Reassembly Procedures for Accessories
7.4.1 Antenna
This section explains how to attach and remove the antenna.
7.4.1.1  Attach the Antenna
With the radio turned off, twist the antenna clockwise onto the connector on the top of the radio.
Figure 7-2.  Attaching/Removing the Antenna
NOTE:If you are using a public safety mic (PSM), the antenna for the PSM must be attached to...

6881094C12-ANovember 11, 2004
Disassembly/Reassembly Procedures: Disassembly/Reassembly Procedures for Accessories 7-7
NOTE:The Motorola-approved battery shipped with the SSE 5000 radio is uncharged. Prior to using 
a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and 
performance.
7.4.2.1  Attach the Battery
1. With the radio turned off, align the baseplate on the bottom of the radio with the groove on the 
top of the battery.
2. Slide the battery toward the latch until it...

November 11, 20046881094C12-A
7-8Disassembly/Reassembly Procedures: Disassembly/Reassembly Procedures for Accessories
4. Re-install the baseplate assembly in the housing assembly (complete up to Step 5. in Section 
7.7.4: “Reassemble the Housing Baseplate” on page 7-17).
Figure 7-4.  Attaching the Belt Clip 
7.4.3.2  Remove the Belt Clip
1. With the battery removed, remove the baseplate assembly from the housing assembly 
(complete up to Step 5. in Section 7.6.4: “Disassemble the Housing Baseplate” on...