Motorola Sse 5000 6881094c12 A Manual

6881094C12-ANovember 11, 2004
Test Equipment and Service Aids: Service Aids 3-5
ChipMaster Nozzles: 
6680333E28 PA nozzle  Soldering and unsoldering ICs 3
6680332E83 PLCC-28* nozzle 
6680332E93 PLCC-32 nozzle 
6680332E82 PLCC-44* nozzle 
6680332E94 PLCC-52 nozzle 
6680332E95 PLCC-68* nozzle 
6680332E96 PLCC-84 nozzle 
6680332E89 QFP-80 nozzle 
6680332E90 QFP-100* nozzle 
6680332E91 QFP-132* nozzle 
6680334E67 QFP-160 nozzle 
6680332E86 SOIC-14/SOL-16J 
nozzle 
6680333E46 SOL-18 nozzle 
6680332E84 SOIC-20...

November 11, 20046881094C12-A
3-6Test Equipment and Service Aids: Field Programming
3.4 Field Programming
This family of radios can be aligned and programmed in the field. This requires specific equipment 
and special instructions. Refer to the Customer Programming Software (CPS) Installation Guide 
(Motorola publication part number 6881095C44) for information on installing the CPS, and to the on-
line help in the CPS for complete field programming information. Refer to Figure 2-9 on page 2-29 
for the...

Chapter 4 Performance Checks
This chapter covers performance checks used to ensure that the SSE 5000 radio meets published 
specifications. The recommended test equipment listed in the previous section approaches the 
accuracy of the manufacturing equipment, with a few exceptions. Accuracy of the test equipment 
must be maintained in compliance with the manufacturer’s recommended calibration schedule. 
Checks should be performed if radio performance degradation is suspected.
4.1 Test Equipment Setup...

November 11, 20046881094C12-A
4-2Performance Checks: Radio Test Mode
4.2 Radio Test Mode 
This section provides instructions for performing tests in display radio test mode.
4.2.1 Access the Test Mode
To enter the display radio test mode:
1. Turn the radio on.
2. Within 10 seconds of turning the radio on, press the one-dot side button five times in 
succession.
The radio shows a series of displays that give information regarding various version numbers 
and subscriber specific information. The displays...

6881094C12-ANovember 11, 2004
Performance Checks: Radio Test Mode4-3
NOTE:All displays are temporary and will expire without any user intervention. If 
information is longer than the physical length of the radio’s display, the information 
will wrap around to the next display.
3. Do one of the following:
•Press the green button on the control top to stop the displays and enter the RF test mode. 
The test mode menu option “1 CSQ” is displayed, indicating test frequency 1
, Carrier 
SQ
uelch mode. See...

November 11, 20046881094C12-A
4-4Performance Checks: Radio Test Mode
NOTE:Once your radio is in a particular test mode, you must turn off the radio and turn it back on 
again to access the other test mode.
4.2.2 RF Test Mode
When the SSE 5000 radio is operating in its normal environment, the radios microcomputer controls 
the RF channel selection, transmitter key-up, and receiver muting, according to the customer 
codeplug configuration. However, when the unit is on the bench for testing, alignment, or...

6881094C12-ANovember 11, 2004
Performance Checks: Radio Test Mode4-5
4.2.3 Control Top Test Mode
This test mode is used to verify proper operation of all radio buttons and switches if a failure is 
suspected.
To perform the control top checks:
1. Press and hold the green button on the control top: the display is backlit, the radio icons are 
displayed, and the LED lights red.
2. Release the green button: “3/0” appears, which indicates that the green button is in the 
open position. 
NOTE:Your radio is...

November 11, 20046881094C12-A
4-6Performance Checks: Receiver Performance Checks
4.3 Receiver Performance Checks
The following table outlines the performance checks for the receiver.
Table 4-5.  Receiver Performance Checks
Test NameSystem AnalyzerRadioTe s t  S e tComments
Reference 
FrequencyRF Control: Monitor
Meter: RF Display
Display: Bar Graphs
Freq: Selected radio TX 
freq.TEST MODE CSQ 
channel* PTT to continuous 
(during the 
performance 
check)UHF R2 (450–488 MHz): 
2.5 ppm
Rated AudioRF...

6881094C12-ANovember 11, 2004
Performance Checks: Transmitter Performance Checks 4-7
4.4 Transmitter Performance Checks
The following table outlines the performance checks for the transmitter.
Table 4-6.  Transmitter Performance Checks
Te s t  N a m eSystem AnalyzerRadioTest SetComments
Reference 
FrequencyRF Control: Monitor
Meter: RF Display
Display: Bar Graphs
Freq: Selected radio TX 
freq.TEST MODE CSQ 
channel* PTT to continuous 
(during the 
performance 
check).UHF R2 (450–488 MHz): 
2.5 ppm
RF...

November 11, 20046881094C12-A
4-8Performance Checks: Transmitter Performance Checks
Notes