Motorola Sb1 Owners Manual

Accessories 4 - 11
Armband
Use the Armband to wear the SB1 on the arm.
To install the armband: Feed the end of the armband through the buckle ensuring that the rubber \
grip side is facing inside.
Hook MaterialRubber Grip Material
Buckle
Figure 4-14Armband
1.Slide the armband onto the arm to a comfortable location.
2.Pull the end of the armband and fold over so that the hook material atta\
ches to the loop material.
Loop Material
Hook Material
Figure 4-15Install Armband
3.Insert the clip of the holster...

4 - 12 SB1 User Guide
Figure 4-16Insert Holster
4.Lift and then pull the end of the armband to tighten.
Figure 4-17Tighten Armband 

Accessories 4 - 13
Lanyard
The lanyard provide a means to hold the SB1 around the neck.
Breakaway Snap
J-hook
Adjustment Buckle
Figure 4-18Lanyard
Slide the lanyard strap through the Adjustment Buckle to adjust the length of the lanyard. Moving the buckle\
 
closer to the Breakaway Snap lengthens the lanyard and moving it away fr\
om the Breakaway Snap shortens 
the lanyard. 

4 - 14 SB1 User Guide
Figure 4-19Adjust Lanyard
The SB1 mounts onto the lanyard and can be removed and replaced with eas\
e. An accelerometer instantly  orients the screen 180° based on device position for easy viewing by \
customers and users.
Figure 4-20Installing the SB1 onto the Lanyard 

Chapter 5 Maintenance & Troubleshooting
Introduction
This chapter includes instructions on cleaning and storing the SB1, and \
provides troubleshooting solutions for potential problems during SB1 operation.
Maintaining the SB1
For trouble-free service, observe the following tips when using the SB1:\
•Do not scratch the screen of the SB1. When working with the SB1, use onl\
y your finger. Never use an 
actual pen, pencil, stylus or other sharp object on the surface of the S\
B1 screen.
•Although the SB1...

5 - 2 SB1 User Guide
•Follow battery usage, storage, and charging guidelines found in this use\
r guide.
•Improper battery use may result in a fire, explosion, or other hazard.
•To charge the mobile device battery, the battery and charger temperatures must be between +32 ºF and +95 ºF (0 ºC and +35 ºC)
•Do not use incompatible batteries and chargers. Use of an incompatible b\
attery or charger may present a 
risk of fire, explosion, leakage, or other hazard. If you have any quest\
ions about the...

Maintenance & Troubleshooting 5 - 3
chlorinated hydrocarbons; acqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; 
benzene; carbolic acid and TB-lysoform.
Cleaning Instructions
Do not apply liquid directly to the SB1. Dampen a soft cloth or use pre-moistened wipes. Do not wrap the 
device in the cloth or wipe, but gently wipe the unit. Be careful not to let liquid pool around the display window 
or other places. Allow the unit to air dry before use.
Special Cleaning Notes...

5 - 4 SB1 User Guide
5.Use a dry cotton tipped applicator and repeat steps 4 through 6.
CAUTIONDo not point nozzle at yourself and others, ensure the nozzle or tube is\
 away from your face.
 
6.Spray compressed air on the contact area by pointing the tube/nozzle abo\
ut ½ inch away from the surface.
7.Inspect the area for any grease or dirt, repeat if required.
Cleaning Cradle Connectors
To clean the connectors on a cradle:
1.Remove the DC power cable from the cradle.
2.Dip the cotton portion of the...

Maintenance & Troubleshooting 5 - 5
Troubleshooting
SB1
Table 5-1Troubleshooting the SB1 
ProblemCauseSolution
SB1 does not turn on.Battery not charged.Charge the SB1.
SB1 was turned off.Place the SB1 into a powered cradle. The SB1 turns on 
when power is applied.
System error.Perform a reset. If the SB1 still does not turn on, contact the 
system administrator. For more information see, 
Resetting 
the SB1 on page 1-5.
Battery did not charge.Battery failed.Perform a reset. For more information see,...

5 - 6 SB1 User Guide
Single Slot Charging Cradle
Table 5-2Troubleshooting the Single Slot Charging Cradle 
ProblemCauseSolution
SB1 battery is not 
charging. Cradle is not receiving power.
Ensure the power cable is connected securely to 
both the cradle and to 
AC power.
The SB1 is not fully seated in  the cradle. Remove and re-insert the SB1 into the cradle, 
ensuring it is correctly seated.
SB1 was placed in the cradle 
upside down. Remove the SB1 from the cradle and insert with 
Scan button facing...