Home
>
Mitel
>
Communications System
>
Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual
Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual
Here you can view all the pages of manual Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 41
SUPERSET 4 Telephone Information Line Appearances 4.23A line is said to “appear” at a SUPERSET 4 telephone if the line has been assigned to one of the available positions on the line status display and can therefore be selected or accessed by the set user. A line can be programmed to appear at one set, at more than one set, or more than once at a particular set. Although a line can appear more than once throughout the system, it is always identified by its unique directory number. 4.24The appearances of...
Page 43
SUPERSET 4 Telephone information 5. PACKAGING General 5.01The SUPERSET 4 telephone is shipped in a single carton, as shown in Figure 5-1. 5.02On delivery at the destination, carefully unpack the SUPERSET 4 telephone carton and check that all items are present and undamaged. Retain some sets of packaging material for reshipment of any damaged items. 5.03The SUPERSET 4 telephone consists of a main assembly, hand- set, and handset cord. Additional items include identification cards (for telephone numbers...
Page 45
SUPERSET 4 Telephone Information 6. INSTALLATION AND MAINTENANCE WARNING ANY CONNECTION OF THIS SET TO AN OFF PREMISE APPLICATION, AN OUT OF PLANT APPLICATION, OR TO ANY OTHER EXPOSED PLANT APPLICATION MAY RESULT IN A SAFETY HAZARD, AND/OR DEFECTIVE OPERATION, AND/OR EQUIPMENT DAMAGE. Note: Installation 6.016.02Do not attempt to use a hand test telephone (butt in) to check SUPERSET 4 telephone lines. There is no loop detector in- stalled in the PABX SUPERSET@ line card/interface; set on- /off-hook...
Page 46
SECTION MITL9109-094-107-NA . l l6.04Install the line identification card and protective lens onto the main assembly. Connect the line cord to the telephone jack. Installation of a SUPERSET 4 telephone into a powered-up sys- tem consists of: Ensuring the local modular telephone outlet is connected to a SUPERSET or COV line card or interface. Connection of the line cord to the main body of the SUPERSET4 telephone. Connection of the line cord to local modular jack. Verifying that automatic initialization...
Page 47
SUPERSET 4 Telephone Information EXAMPLE OF TELEPHONE NUMBER IDENTIFIED ON TELEPHONE NUMBERn IIIDENTIFICATION CARD PROTECilVE LENS TELEPHONE NUMBER IDENTIFICATION CARD / PROTECTIVE HAND&T CORD MAIN AiSEMBLYREAR SiPPORT(OPTIONAL) 6743EZRZFigure 6-l SUPERSET 4 Telephone Assembly Page 25
Page 49
SUPERSET 4 Telephone information 7. SUPERSET 4 TELEPHONE TEST PROCEDURES General 7.01Perform these SUPERSEJ b-test procedures as operational tests after initial installation of a system. 7.02Whenever a SUPERSEJ 4 telephone is connected to an operat- ing system, or the system has just been powered up, this test is run automatically. A message in the following format appears on the SUPERSEJ 4 telephone LCD: “:SS4 VXX.XX.XX:“, for approximately 30 seconds. Time and date are then displayed. If the test...
Page 50
SECTION MITL9109-094-107-NATABLE 7-1 INSTALLER LOOP TEST ROUTINES StepActionVerification Notes Accessing Test Routines 1.Go off-hook (handset or handsfree).Dial tone returned.1Line status display indicates line busy at this set. “TEST! PRESS KEYS” displayed. 2, 3 DTMF tones are heard through handset or speaker. A 2-digit number is displayed as follows:2.Dial Loop Test Access Code. Keypad Test 3.Press keys l-9,*, 0, and # in turn. Supplementary Feature Keys Test KeyNumber PressedDisplayed 101 202 3034 04...