Home
>
Mitel
>
Communications System
>
Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual
Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual
Here you can view all the pages of manual Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 11
SECTION MITL9109-094-I 06-NA speed dial numbers on selected speed dial keys. SPEAKER ON/OFF -This key allows the set user to receive or origi- nate calls without using the handset. Each time this key is pressed the set is switched between handset and Handsfree operation. MHZ/MUTE - While pressed, the MIC/MUTE key disables the micro- phone during Handsfree operation, either to prevent transmission of local sound or to improve reception when the set is installed in a noisy environment. Speaker Volume...
Page 12
SUPERSET 3 Telephone Description 220 mm(8.66 in.)- IWEIGHT: 1 kg. (2.2 lb)161 mm (6.31 in.) Figure 3-l SUPERSET 3 Electronic Telephone Set Page 7
Page 13
SECTION MITL9109-094-106-NA SWITCHHOOK \ SPEAKERVOLUME CONTROLSPEAKER -ASSEMBLY PITCHRINGER VOLUMECONTROLCONTROLLINE IDENTIFICATION e .-\-[I I 1 \- II I hold‘El trans/confswap noprogram/save onspeaker on/off IOmic/mute 00 redialI 1 - SPEED DIALKEYS / 3 LlNEINDICATORS LINE SELECT/SPEED DIAL KEYS IMICROPHONEKEVPADINPUT KA0505EZR2Figure 3-2 SUPERSET 3 Telephone Face Layout Page 8
Page 14
SUPERSET 3 Telephone Description 4. SHIPPING AND RECEIVING General 4.01The SUPERSET 3 telephone is shipped in a single carton. 4.02The SUPERSET 3 telephone is disassembled into main assem- bly, handset, handset cord, and line cord. Additionai items in- clude identification cards (for telephone numbers and lines), clear plastic lens for these cards, reference guide, installation guide, and warranty tag. Delivery Check 4.03On delivery at the destination, check that all items are present and undamaged....
Page 16
SUPERSET 3 Telephone Description 5. INSTALLATION WARNING ANY CONNECTION OF THIS SET TO AN OFF PREMISE APPLICATION, AN OUT OF PLANT APPLICATION, OR TO ANY OTHER EXPOSED PLANT APPLICATION MAY RESULT IN A SAFETY HAZARD, AND/OR DEFECTIVE OPERATION, AND/OR EQUIPMENT DAMAGE. General 5.01Installers should not use a hand test telephone (butt-in) to check a SUPERSET 3 telephone line. The interface card for SUPERSET 3 telephones has no loop detector; set on-hook/off-hook status is signaled by data transmission....
Page 18
SUPERSET 3 Telephone Description 6. TEST PROCEDURES General 6.01Perform these test procedures as operational tests when in- stalling a SUPERSEJ 3 telephone after initial installation of a system. 6.02Whenever a SUPERSET 3 telephone is connected to an ‘operat- ing system, or the system has just been powered up, the test is run automatically and the following results appear. If any test fails, verify that the system is installed correctly and is powered up. SUPERSET 3 TELEPHONE, POWER-ON TEST TEST...
Page 19
MITEL STANDARD PRACTICESECTION MITL9199-094-107-NAIssue 1, April 1988 SX-200” DIGITAL PRIVATE AUTOMATIC BRANCH EXCHANGE (PABX) SUPERSET 4” TELEPHONE INFORMATION @Copyright 1988, MITEL Corporation. All rights reserved, T”Trademark of MITEL Corporation @Registered Trademark of MITEL Corporation
Page 20
SECTION MITL9109-094-107-NANOTICE The information contained in this document is believed to be accurate in all respects but is not warranted by Mite1 Corporation (MITEL). The information is subject to change without notice and should not be construed in any way as a commitment by Mite1 or any of its affiliates or subsidiaries. Mite1 and its affiliates and subsidiaries assume no responsibility for any errors or omissions in this document. Revisions of this document or new editions of it may be issued...