Home > Mitel > Communications System > Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Here you can view all the pages of manual Mitel SMART L CALL CONTROLLER Hardware Installation Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 101

SECTION 8350-345-014-NA ISSUE 1, JUNE 1988 
10. CDR AND CMNPNG 
Example 2 
Someone enters DTMF Chain Programming Mode at Controller 5 in a Chain, programs 
“523 8 980 01270945 009 2” and then goes on-hook. 
!5i38$8~012709450092X SOH>‘-YNUL>- ; 
T I A 
I I 
ENQUIRY PROGRAMMING COMMAND TO START-OF-CDR- 
CHARACTERS INFORMATION DUMP CDR IN DUMP 
CONTROLLER 5 CHARACTER 
ENQUIRY 
CHARACTERS 
On paper, the output (t) from the above would be: 
. . . 
(previous CDR record)...... ..CHN!523898001270945Oo92x--;...

Page 102

ISSUE 1, JUNE 1988 
SECTION 8350-345-01 d-N.4 
10. .CDW AND CHAINING 
10. 4. Enabling CDR 
You can change Call Detail Recording (CDR) format as required: 
0 The MITEL format was developed for PBX applications (specificaiiy MITEL PBXs). 
Some fields are used..for call .transfers, ~attendants, eta, -and .are not supplied by the 
Controller. 
l The MART format is similar to*the MITEL format, however it has reduced the printing 
width to fit in 80 columns and the R field is in ASCII instead of numeric. 
For...

Page 103

SECTION 8350-345-014-NA ISSUE 1, JUNE 1988 
11. CHAINING CONDITIONS 
Certain conditions and restrictions apply to Controllers and Chaining. This part outlines 
those restrictions under these headings: 
Parameter 013 
Parameter 014 
Chains 
Other N&es 
11. 1. Parameter 013 
A Controller may be in one Chain only, and the Controller must have a unique ID as set 
by 013T. 
The Controller must be programmed such that 013T is the same as the number you 
labeled the RS-232 connector, on the Chaining Cable. 
The...

Page 104

* 
ISSUE 1, JUNE 1988 SECTION 8350-345-014-NX 
11. CHAINING CONDITIONS 
It is not necessary to use DTMP Chain Programming if a Chaining Cable is connected to a 
Controller; “normal” DTMF programming may still be done for that Controller as before, 
if desired; only if command 950 is dialed will that Controller (and the rest of the Chain) 
enter the DTMF Chain Programming mode. 
A printer is NOT necessary to perform DTMF Chain Pro&ramming;;If a printer is at- 
tached to the printer port of a Chaining...

Page 105

SECTION 8350-345-o 14-NA 
INDEX 
C 
CDR AND CI-iAINING, 3.14 
CHAINING: CONDITIONS,- 3:17, 3-18 .: 
CHAINING DATA VERIFICATION. 3.13 
CDR buffering. 3.15 
F 
FIGURE, 3.2 
P 
Parameter 013, 3.17 
Parameter 014, 3.17 
S 
SETTING UP A CHAIN, 3.3 
Suspending CDR. See CDR buffering ISSUE 1, JUNE 1988 
PAGE - 3.19  

Page 106

MlTEL ENGINEERING  PRACTICE 
SECTlON MITL8350-047-l  OO-lVA 
.’  Issue 2, May  1985 
i  ’ 
COMMON  CARRIER ACCESk “PIALER 
AND  CALL  CONTROLLER 
GENERAL  INFORMATION  lh. ‘!’ 
0 - Copyright  of MITEL  DATACOM  INC.‘1985 
m  TM 
- Trademark  of MITEL  DATACOM  INC. 
:t. , 
. 
i w  - Registered  Trademarksof  MITEL CORPORATION  ‘z;  

Page 107

SECTION MITL8350-047-IOO-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK ---  

Page 108

SECTION MlTL8350-047-l OO-NA 
NOTICE TO U.S. CUSTOMERS 
The information contained in this document is believed to be accurate in all respects but is 
not warranted by MITEL DATACOM INC. The information is subject to change without notice 
and should not be construed in any way as a commitment by MITEL DATACOM INC. or any 
of its affiliates or subsidiaries. MITEL DATACOM INC. and its affiliates and subsidiaries 
assume no responsibility for any errors or omissions in this document. Revisions of this...

Page 109

SECTION MITL8350-047-l OO-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
._ 
i 
_ 
i 
.I 
L 
Page ii  

Page 110

SECTION MlTL8350-047-IOO-NA 
NOTICE TO CANADIAN CUSTOMERS 
The information contained in this document is believed to be accurate in all respects but is 
not warranted by MITEL DATACOM INC. The information is subject to change without notice 
and should not be construed in any way as a commitment by MITEL DATACOM INC. or any 
of its affiliates or subsidiaries. MITEL DATACOM INC. and its affiliates and subsidiaries 
assume no responsibility for any errors or omissions in this document. Revisions of this...
Start reading Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Related Manuals for Mitel SMART L CALL CONTROLLER Hardware Installation Manual

All Mitel manuals