Minolta Di450 User Manual

5-10
2. Image Memory Input
Using the Utility Mode
Chapter 5
Press the Utility key.
Touch [Job/Image/Scan Input].
Touch [Image Memory Input].Touch [Delete], then touch the number key to
be deleted.
To u c h [ E n t e r ] .
Deleting a Programmed Image
1
4002O282CA
2
4003P142CA
3
4003P152CA
4
4003P465EC
5
Downloaded From ManualsPrinter.com Manuals 

5-11
Using the Utility Mode
Chapter 5
3. Meter Count and Toner Replenisher
Meter Count
Touching [Meter Count] allows you to check the total count of each of the following seven counters
recorded since the installation of the machine.
Shows the total number of prints made since the
installation of the machine.
Shows the number of prints made on paper of a
preset size. (The size will be set by your Technical
Representative.)
Shows the number of 2-sided prints made.
Shows the number of 2-sided prints made...

5-12
Using the Utility Mode
Chapter 5
4. User’s Choice
The machine has been set so that the most frequently used settings are automatically selected in the initial
mode. User’s Choice allows you to select the default settings which are automatically selected in the
initial mode according to your own needs. This saves time and effort to make extra settings when the
machine is turned ON or Auto Panel Reset is activated.
For more details, consult your Technical Representative.
User’s Choice Functions
[1/6]
...

5-13
4. User’s Choice
Using the Utility Mode
Chapter 5
Useful Tip
When“100 Accounts” is selected, the User’s
Choice functions of [1/6] to [4/6] can be set for
each account after the corresponding access
code has been entered. (In this case, the listing of
User’s Choice displayed on the Touch Panel is
from [1/4] to [4/4].)
The administrator can make the User’s Choice
settings in common with all 100 accounts after
“100 Accounts” has been selected.
➀With the Touch Panel prompting you to enter
the access...

5-14
4. User’s Choice
Using the Utility Mode
Chapter 5
[2/6]
Select whether to enable (“ON”) or disable
(“OFF”) recalling a default zoom ratio for 2in1,
4in1, or Booklet Creation. Setting is possible for
“2in1/4in1” and “Booklet Creation.”
 “2in1/4in1”
Default zoom ratios:
2in1: 0.647
4in1: 0.500
The initial setting is “ON.”
 “Booklet Creation”
Default zoom ratios:
Booklet Creation: 0.647
The initial setting is “ON.”
Select the default density setting selected
automatically in the initial mode. Select...

5-15
4. User’s Choice
Using the Utility Mode
Chapter 5
[3/6]
Select whether to enable (“ON”) a copy cycle or
not (“OFF”) when it is initiated by pressing the
Start key with no originals placed on the Original
Glass or with an original smaller than the
detectable size placed on the glass in the Auto
Paper mode.
If this function is turned “ON,” the copy cycle is
run using the paper loaded in the default paper
source. If turned “OFF,” a warning message
appears to instruct the user to select the paper.

The...

5-16
4. User’s Choice
Using the Utility Mode
Chapter 5
[5/6]
Select either “Auto Detect” or “Size Input” for the
size of the paper loaded in the Universal Tray.
The initial settings are as follows:
1st Drawer: “Auto Detect”
2nd Drawer: “Auto Detect”
Designate a drawer for special paper.
The initial setting is “Normal” for all drawers.
See p. 3-10 for Special Paper Setting.
Select the time it takes the auto panel reset
function to be activated from among “30 seconds,”
“1 min.,” “2 min.,” “3 min.,” or “5...

5-17
4. User’s Choice
Using the Utility Mode
Chapter 5
Making the User’s Choice Settings
Press the Utility key.
Touch [User’s Choice].
Select the key of the page number on which
the desired User’s Choice function is listed.
For example, to change Output Priority from
Non-Sort to Sort, touch [2/6].Touch the key of the desired User’s Choice
function.
For example, touch [Output Priority].
To u c h [ S o r t ] .
To u c h [ E n t e r ] .
*Repeat steps 3 to 6 to make new settings for
other User’s Choice...

5-18
Using the Utility Mode
Chapter 5
5. Administrator Mode
This mode is used only by the administrator of your machine. When Administrator Mode is selected, the
machine prompts you to enter your “Administrator’s #.” The following functions can be set only when
the correct administrator number is entered.
NOTES
 The administrator number is to be programmed by your Tech. Rep. Ask him/her for more details.
 The administrator of this machine should remember the administrator number.
Selecting the...

5-19
5. Administrator Mode
Using the Utility Mode
Chapter 5
Administrator Mode Functions
This function is used to control the number of
pages printed according to the account.
Select whether to turn “ON” or “OFF” the Copy
Track function for “Copier” or “Printer” and select
the Copy Track method, either “100 Accounts” or
“1000 Accounts.”
The initial setting is “OFF.”
When“100 Accounts” is selected:

Access Code:
You can program or change your access code
(for a max. of 100 accounts).

Account No.:
Program...