Miele Wt 2670 Wpm Operating Instructions

Front view
aInlet hose (with flexible, waterproof
metallic outer sleeve)
bElectricity supply cable
c-fFlexible drain hose (with
detachable swivel elbow)
gControl panelhDetergent dispenser drawer
iDrum door
jAccess to drain filter, drain pump and
emergency release
kHandle recesses for moving the
machine
lFour height adjustable feet
Installation and connection
61
 

Rear view
aProtruding lid for holding when
moving the machine
bElectricity supply cable
cTransit bar covers
dInlet hose (with flexible, waterproof
metallic outer sleeve)
eDrain hose
Installation and connection
62
 

Installation surface
A concrete floor is the most suitable
installation surface, being far less
prone to vibration during the spin cycle
than wooden floorboards or a carpeted
surface.
Please note the following points:
^The machine must be level and
securely positioned.
^To avoid vibrations during spinning,
the machine should not be installed
on soft floor coverings.
If installing on a wooden joist floor:
^We recommend a plywood base (at
least 59x52x3 cm) The base should
span several joists and be bolted...

^Using the spanner supplied turn the
left-hand transit bar 90°, then
^
withdraw the transit bar.^Turn the right-hand transit bar 90°,
then
^
withdraw the transit bar.
Installation and connection
64
 

,To avoid the risk of injury the
holes for the transit bars must be
covered after the transit bars have
been removed.
^Fit the covers on to the two holes.
Then plug the holes as shown with
the caps.
,The machine must not be moved
without the transit fittings in place.
Store them in a safe place for future
use. They must be re-fitted if the
machine is to be moved again (e.g.
when moving house).
Re-fitting the transit bars
Re-fitting is carried out byreversing the
procedure.
Levelling the machine
The...

Screwing out and adjusting the feet
The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.
^Using the spanner supplied turn
counter nut2in a clockwise direction.
Then turn counter nut2together with
foot1to unscrew.
^Use a spirit level to check the
machine is standing level.
^
Hold foot1securely with a pipe
wrench. Turn counter nut2again
using the spanner supplied until it
sits firmly up against the housing.
,All four counternuts must sit...

The Miele water protection
system
The Miele water protection system
protects machine from water damage.
The system consists of three main
components:
1) the inlet hose
2) the electronic unit and the machine
housing
3) the drain hose
1) Inlet hose
– The inlet hose is tested to withstand
pressure of more than 14,000 kPa.
– It has a protective sleeve which is
made from metal to protect the hose
from damage.
2) Electronic unit and machine
housing
– Sump
Any leaking water is collected in a
sump in the base of...

Connection to the water
supply
The machine should be connected to a
mains water supply in accordance with
local and national safety regulations.
The German authorities do not require it
to have a non-return valve as the
washer-dryer has been designed to
comply with DIN regulations.
The machine is designed to operate
with a flow pressure of between
100 kPa and 1,000 kPa. If it is higher
than 1,000 kPa it is essential to fit a
reducer valve.
Connection to the mains water supply
should incorporate a mains...

Connection to the drainage
system
The machine drains via a drain pump
with a delivery head of 1 metre. The
drain hose must not be kinked as this
restricts drainage. The swivel elbow at
the end of the hose can be turned in
either direction, or can be detached if
required, with a sharp twist and pull.
If required the drain hose can be
extended to a length of 5 m. The
necessary parts can purchased from
the Miele Spare Parts Department or
your Miele dealer.Drain hose connection:
1. Direct into a sink or...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person, in strict accordance with
national and local safety regulations.
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains supply.
The voltage and connected load are
given on the data plate. Please ensure
these match the household mains
supply. The...