Miele Pw 6065 Operating Manual

Standby
The display goes out after 10
minutes and the Start button
flashes slowly to save energy.
On
The display will go into Standby mode:
–if no program was selected after the
machine was turned on.
–after a program has started.
–at the end of a program.
Not in current prog.
(Factory default)
The Standby function will be turned on
if no program was selected after the
machine was turned on.
By turning the jog shuttle or pressing
any button the display is turned on
again.
Memory
The Memory function...

The menu Settings - Supervisor level must be activated
by the Technical Service.
The menu Settings (except LanguagesJ) is locked with a
code to prevent unwanted access.
Selecting Settings
SettingsBackA
LanguageF
Supervisor level
^Select Supervisor level and confirm.
SettingsBackA
Supervisor levelAccess via code
^Select Access via code and confirm.
Entering the code
Enter the code 0 0 0 (factory default). If the code is entered
wrong three times, the code entry will be locked for 1 hour.
0__
Enter code
^...

Confirming the code
0 0 0
Confirming the code
OK
HBackA
H
^Confirm the entered code.
WEntry OK
Menu opened
The user is now in the Supervisor level. The previously
described and all the following settings can be changed.
Change the code to prevent unauthorized access to the
settings.
Menu Settings - Supervisor level
63
 

LanguageJ
The display contents can be shown
in different languages.
The fixed default language can be set
in the sub-menu LanguagesJ.
^Select the desired language and
confirm with OK.
Sort languages
The language order can be set,
when the option Language access -
international is selected.
Supervisor level
The access code for the operator
level can be changed.
^
Enter the old code.
^
Enter the new code.
Once the new code is confirmed, the
display will show the beginning of the
Settings menu.
Language...

Auto load control
The washer has a Auto load control.
The water levels and the program
running times are adjusted to the
load size. If the load size automatic
is turned off the program will always
run as if for a full load.
The machine comes factory set with
this option turned on.
Pre-wash water
The water type for the pre-wash can
be selected (except for the program
Curtains). The hot water intake will
be only accessible at a wash
temperature of 86°F (30°C) or
higher.
The machine comes factory set with...

Water level Cottons
The program Cottons Hygiene and
Cottons Uni. allows you to increase
the water level for the main wash.
The machine comes factory set with the
option block parameter selected. (The
water level will be controlled according
to the factory set program data.)
Water level Min. iron
The program Minimum iron allows
to increase the water level for the
main wash.
The machine comes factory set with the
option block parameter selected. (The
water level will be controlled according
to the factory...

No. of programs
Additional programs can be added
to the program selection.
0  Additional programs (factory default)
4  Additional programs (Table linen,
Pillows, Curtains and Kitchen
linen)
2  Additional programs (Outerwear
and Waterproofing)
6  Additional programs (all of the
above).
Hygiene
If the last used program had a
temperature of 55°C or less, the
display shows the request to start
the Hygiene program.
The machine comes factory set with
this option turned off.
Sluice
When the option is selected...

Optimize energy
The energy use for the programs
Cottons Hygiene, Cottons Uni.
and Minimum iron is at its optimum
when this option is turned on.
The machine comes factory set with
this option on.
No. rinses Cottons
The programs Cottons Hygiene
and Cottons Uni. allow you to
change the number of rinse cycles.
2 rinses (factory default)
3 rinses
4 rinses
5 rinses
No. rinses min. iron
The program Minimum iron allows
you to change the number of rinses.
2 rinses (factory default)
3 rinses
4 rinses
Pre-rinse...

No detergent
If an external dispensing system is
fitted to the machine it will not be
accessed if No soap is selected.
You have the option to show the
Extra No Soap in the menu Extras.
The machine comes factory set with
this option off.
External dispenser
The washer is set up for connection
to an external dispensing system. To
use the external dispensing system
the setting must be adjusted/set
accordingly.
The machine comes factory set with
this option off.
Leaving the Settings menu
^Press back and...

70