Miele Pw 6065 Operating Manual

Water connection
Cold water connection
A water faucet with
3/4 threat must be
provided on-site. If none is available the
machine must be connected to a water
line by a qualified plumber.
The water pressure must be within
14.5 -145 psi (1 -10 bar). If the water
pressure is greater than 145 psi
(10 bar), a pressure reducer must be
installed. If the water pressure is below
15 psi (1 bar), there will not be enough
water available for a complete fill.
The cold water hose (blue mark) is
notsuitable for a hot...

Hot water connection
Connecting the machine to a hot water
ring line will lead to low electrical
consumption during hot water
operation. The hot water temperature at
the water faucet must not exceed 158°F
(70°C).
The water in single water lines from the
hot water source cools faster when not
in constant use. To heat the wash water
more electricity must be used. The
same conditions for the hot water as for
the cold water connection will then
apply.
^Connect the hot water intake hose
(red mark) to the...

Drainage
Drain valve
The machine is drained with a
motorized drain valve. A connection
can be made to an on-site floor drain
(gully with an air gap) on an angle.
Drain pump
The wash water is drained using a
pump with a 3 ft (1 m) delivery height.
Make sure there are no kinks in the
drain hose. The elbow on the end of the
drain hose can be turned or removed if
necessary.
Possible connections:
1. Directly into a sink:Hook the hose
over the edge of the sink and secure
it firmly (e.g. by tying the hose to...

Electrical connection
,This installation should be
performed by an experienced and
qualified technician, in accordance
with local codes and regulations.
The washer comes with a power cord
without a plug.
The machine is supplied as standard
for connection to a 208 V, 60 Hz, 20 A,
3-phase electrical supply.
For extra safety it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA.
The machine must only be connected
to the voltage and frequency shown on
the data plate.
,To...

Height 85 cm
Width 59.5 cm
Depth 72 cm
Depth with the door open 112 cm
Weight 109 kg
Maximum floor load 2778 Newton (approx. 278 kg)
Capacity 6.5 kg dry laundry
Fuse rating see data plate
Rated load see data plate
Fuse rating see data plate
Noise level during spinning
(Noise emission 3. GSGV)< 70 dB(A)
Minimum water flow pressure 14.5 psi (1 bar)
Maximum water pressure 145 psi (10 bar)
Length of intake hose 1.6 m
Length of power cord 1.6 m
Drain height maximum (Drain pump) 1 m
Light bulb for drum light...

Disposal of the packing
materials
The cardboard box and packing
materials protect the appliance during
shipping.
To prevent suffocation of children
ensure that any plastic wrapping, bags,
etc. are disposed of safely and kept out
of the reach of children.
Please recycle.
Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure that the appliance presents no
danger to...

Menu SettingsJ
to adjust standard settings
The washer electronic can be adjusted to changing demands with the settings.
The settings can be changed at any time.
 

Opening the menu Settings
1 Cottons Uni. 60°C Program selection
2 Minimum iron 40°CSettingsF
3 Delicates 40°C
4 WoollensH30°C12:00
^Select the SettingsJin the main menu and confirm by
pressing the jog shuttle.
Selecting Settings
SettingsBackA
LanguageF
Water plus
Suds coolingH
^Select the settings to be changed and confirm.
If no selection was made in the sub-menu, the display will
switch back to the Settings menu after 20 seconds.
Leaving the Settings menu
^Press Back and confirm. The display shows the...

LanguageJ
The display contents can be shown
in different languages.
The displayed language can be set in
the sub-menu LanguageJ.
^Select the desired language and
confirm with OK.
The flag behind the word Language is
a guide to find the settings menu in
case a foreign language is shown.
If the language setting was changed, it
is only valid for the current wash
program. Once the program ends, the
display will show the language which is
set under Settings - Supervisor level.
Water plus
In the setting Water...

Time of day
The selection allows the clock to be
shown as 24 hours, 12 hours or not
at all. The time of day is also set
here.
If the clock is not selected the delay
start can only be shown only as a 24
hour clock timer. The display will how
the timer counting down until the start
of the program but not he current time
of day.
Selecting the clock
^Select the clock display and confirm.
The display changes to the time of day
setting.
Set the time of day
^Select the current hour with the jog
shuttle and...