Miele Pw 6065 Operating Manual

Changing the light bulb
A burnt out light bulb will not affect the
performance of the washer.
^Disconnect the power supply to the
work area by unplugging the unit,
tripping the circuit breaker or
removing the fuse.
^Open the detergent dispenser
drawer. Remove the tool from the rear
side of the panel.
^Open the drum door.
^
Insert the tool into the slit of the light
bulb, turn counterclockwise until
resistance is felt.
^
Pull out the drum lighting.^Press together the hooks of the
plastic fitting,2, to...

Repairs
In the event of a fault which you cannot
fix yourself, please contact the Miele
Technical Service Department.
l1 800 565-6435
[email protected]
When contacting the Technical Service
Department, please quote the model
and serial number of your appliance.
Both can be found on the data plate
visible above the front glass on the
inside of the door.PC Update
The indicator marked PC allows a
technician to make use of new
technology if new programs are
developed or new fabrics are
introduced.
Optional...

Installation Instructions
 

Front view
aWater intake hose cold
bWater intake hose hot
cElectrical connection
dControl panel
eDetergent dispenser drawer
fDrum doorgAccess panel to drain filter, drain
pump and emergency door release
hHeight adjustable feet
iStand
jRetaining clips (for concrete stand)
kRecessed grip
Installation
44
 

Rear view
aLid with transport grips
bMounting for:
–
Water intake hose
–
Drain hose
–
Withdrawn shipping struts
cPower corddShipping struts with rotary protectors
eWater intake hose (cold)
fWater intake hose (hot)
gDrain hose for drain pump
hDrain hose for drain valve
iHeight adjustable feet
Installation
45
 

Washer/ Dryer Stack
Height:
Stacking kit with pull out shelf
66
15/16 (170 cm)
The Miele washing machine can be
installed as part of a washer-dryer
stack in combination with a Miele
tumble dryer. An appropriate stacking
kit* is required.
Installation of the stacking kit must be
provided by a Miele Service Technician.
Reinstallation of the machine lid
When reinstalling the appliance lid,
check the firm fit of the cover at the rear
bracket for a safe transport of the dryer.
Installation on a base
The...

Installation site
The washer cannot be built-in.
,Do not install the machine
directly next to or over an open floor
drain or drain channel. Moisture can
penetrate the machine and damage
electrical parts.
A concrete floor is the most suitable
surface for the washer. Concrete floors
are less prone to vibration during the
spin cycle than wooden floors.
,If the machine is installed on a
masonry or concrete base itmust
be secured with retaining clips to
prevent the washer from vibrating off
the stand during...

^Turn the left shipping strut
counterclockwise 90° with the
enclosed combination wrench.
^
Pull the shipping strut out.^Turn the right shipping strut
counterclockwise 90° with the
enclosed combination wrench.
^
Pull out the shipping strut out.
Installation
48
 

^Close the holes with the rotary
protectors and their caps.
^
Fasten the shipping struts at the rear
side of the washer. Take care to insert
the drill holes,b, into the clamps,a.
,Movement of the washer without
the shipping struts in place should
be kept to a minimum. The shipping
struts should be stored on the back
of the washer for future use. They
must be reinstalled before moving
the machine.
Installing the shipping struts
^Reinstall the struts by reversing the
installation procedure.
Installation
49
 

Leveling the washer
To ensure smooth operation the washer
must be level.
Failure to level the machine can result
in increased water and energy
consumption as well as the washer
banging during the spin cycle or
walking across the floor during use.Adjust the four leveling feet
The washer is leveled by adjusting the
four feet. The machine is boxed with the
feet completely screwed in.
^Turn the locking ring,2, counter-
clockwise with the enclosed
combination wrench. Unscrew each
of the four feet as much as...