Miele Kfn 14827 Sdeed Operating And Installation Instructions

^Remove caplfrom the bearing
bush in the door and refit on the
opposite side.
Refitting the lower door
^
Unscrew threaded pindby one turn
using the allen key supplied.
^
Pull hinge pinatogether with discb
and adjustable footcupwards and
off.
^
Remove cover cape.^Undo screwsfand take hinge plate
goff.
^Unscrew partifrom hinge plateg,
rotate it by 180° and refit into the hole
on the opposite side of the hinge
plate.
^Refit cover capein the other hole.
^Unscrew threaded pindfully using
the allen key...

^Screw hinge plateginto position on
the opposite side using the twoouter
long slots only. To make it possible to
align the door later, do not replace
thecentrescrew at this stage.
^Important. Screw the adjustable foot
cinto hinge pinaas far as it will go.
^Place hinge pinatogether with disc
band adjustable footcwith the
guide at the end of the threaded pin
and screw it in.
^Then tighten threaded pind.
^
Place the lower door onto hinge pin
cfrom above.
^
Close the lower door.^Fit hinge piniinto middle...

^Insert the soft-close mechanism back
into the door, starting at the right
hand side.
^Slide the soft-close mechanism back
into the door as far as it will go
towards the appliance using a
flat-headed screwdriver.
The screw holes on the left and right
must line up perfectly.
^
First screw the soft-close mechanism
onto the appliance side, then onto
the handle sidec, pushing it firmly
towards the appliance.^Attach panelbto soft-close
mechanism bracketd.
^Align bracketdto the hinge plate,
and insert pinefrom...

Refitting the upper door
^Then fit the upper door on middle
hinge pini.
^Close the upper door.
^Fit hinge platenonto the opposite
side and secure it with screwsm.
If necessary drill pilot holes for the
screws or use a battery operated
screwdriver.
^Refit coverkon the opposite side.
^Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the
screws.Replacing the upper soft-close door
mechanism
^Remove coverafrom panelb,
rotate it by 180° and refit it on the...

^First screw the soft-close mechanism
onto the appliance side, then onto
the handle sidec, pushing it firmly
towards the appliance.
^Attach panelbto soft-close
mechanism bracketd.
^
Push covereon from the side so
that the openings for the pinfare
vertically aligned.
^
Align bracketdto the hinge plate,
and insert pinffrom above so that
the right angle fits into the recess.
^
Clip covereinto position.Make sure that coverefits properly so
that the door can be closed without
hindrance and the pin is...

Refitting the handles
Please make sure you follow the
instructions below carefully when
you refit the handles. The door seal
will be damaged if the handle is
fitted incorrectly.
^Loosely attach the handle to the
opposite side of the door with the two
front screwsb.
Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,
^
tighten both threaded pinsawith a
suitable allen key until mounting plate
clines up...

The appliance doors can be aligned
with the housing after they have been
fitted.
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
To align thelower dooruse the long
outer slots in the lower hinge plate:
^Remove centre screwafrom the
hinge plate.
^
Slightly loosen both outer screwsb.
^
Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be used again.To align theupper...

aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work...

79
 

Alteration rights reserved / 3611
KFN 14827 SDE ed/csM.-Nr. 09 021 030 / 02