Miele G 892 Scu Plus Manual

Running the dishwasher
^Make sure the spray arms are not
blocked.
^Close the door.
^Turn on the dishwasher.
The Start/Stop indicator (17) will flash
and a program indicator (14) will light.
^Select a wash program using the
program selection buttons (19). The
selected program indicator will light.
^
Refer to the Program guide for
details on wash programs.
^
Select Top Solo if desired. See
Additional features.
^
Press the Start/Stop button (17).
The wash program will begin.
Do not end a program...

At the end of a program
The End indicator will light when the
program has finished.
^Turn off the dishwasher.
^Open the dishwasher door slightly to
allow the dishes to cool before
unloading.
It is advisable to turn off the water
supply if the dishwasher will not be
used for a period of time (e.g. while
vacationing).
Interrupting a program
A program is interrupted as soon as the
door is opened.
If the door is closed, the program will
continue from where it was interrupted.
,Water in the dishwasher may be...

Program guide
Program When to use Program cycle
Pre-
wash
12Main
washInterim
rinse
12Final
rinseDry-
ing
Pots & Pans for heavily soiled pots and pans with dried on food
Main wash temperature170 °F (75 °C)
Run-time128 minXX X X - X X
Sani Wash extended wash time
forsanitizing normally soiled dishware with dried
on food
Main wash temperature150 °F (65 °C)
Run-time142 min-X X XX X X
Normal Plus higher wash temperature helps to clean
normally soiled dishware with stubborn dried on
food or greasy residues...

Additional features
"Top Solo" (18)
Using Top Solo will save water and
energy.
This program is recommended when
there is only a small load to clean. Top
Solo can be selected with all
programs.
With this feature, water is directed only
to the top and middle spray arms in the
dishwasher. This means that the water
jets are only aimed at items in the
upper basket and the cutlery tray.
The middle spray arm also directs
water downwards, so lightly soiled
plates or platters can be placed in the
lower...

Extended drying
If desired drying results are not
consistently achieved, the turbothermic
cooling fan can be programmed to run
an extra 14 minutes at the end of each
program.
The Extended drying feature can also
be activated to prevent condensation
from collecting on the steam deflector.
Turning extended drying on/off
^Make sure the dishwasher is turned
off.
^Press and hold the Start/Stop (17)
button and at the same time turn the
dishwasher on using the On/Off
button.
Release the Start/Stop button...

With the aid of the following guide, minor problems can be fixed without a service
call.
,Repairs should only be carried out by a qualified and trained person in
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage.
What if … Possible fault Fix
the dishwasher does not
start?The door is not properly
closed.Close the door firmly.
The machine is not
plugged in.Insert the plug.
The fuse is defective or
the breaker has tripped.Reset the...

What if … Possible fault Fix
the "Drain" indicator
flashes and the program
stops?The triple filter in the wash
cabinet is clogged.Clean the filter, see
maintenance instructions.
The drain pump or the
non-return valve may be
blocked.Clean the drain pump and
the non-return valve, see
maintenance instructions.
The drain hose is kinked. Remove the kink.
the "End", "Start/Stop"
and "Top Solo"
indicators flash at the
same time at the end of
a program?There may be a technical...

What if … Possible fault Fix
there is a knocking
noise in the wash
cabinet?The spray arm is hitting
an item in the basket.Interrupt the program,
rearrange items blocking
the spray arms.
there is a rattling noise?Items are not secure in
the wash cabinet.Interrupt the program and
rearrange loose pieces.
there is a knocking
noise in the water
pipes?This may be caused by
the installation or the
diameter of pipe.This has no effect on the
dishwasher. If in doubt
contact a plumber.
the dishes are not dry,...

What if … Possible fault Fix
tea or lipstick stains
have not been
completely removed?The wash temperature of
the selected program was
too low.Select a program with a
higher temperature.
Not enough detergent
was used.Use more detergent.
white residue is visible
on cutlery and dishes,
clouding occurs on
glassware and film can
be wiped off?Not enough rinse aid was
used.Increase the dosage,
see Before using for the
first time.
The salt reservoir is
empty.Add reactivation salt,
see Before using for the
first...

What if … Possible fault Fix
plastic items are
discolored?Natural dyes e. g. from
vegetables may be the
cause. Not enough
detergent was used to
break down natural dyes.Use more detergent, see
Adding detergent.
Discoloration is
permanent.
there are rust stains on
cutlery?The salt reservoir cap was
not screwed on properly.Reseat and screw the cap
on firmly.
The affected items are not
corrosion resistant.There is no remedy.
Only wash dishwasher
safe cutlery.
detergent is left in the
dispenser at the end of...