Miele G 892 Scu Plus Manual

Wash cabinet
1 Upper spray arm (not visible)
2 Cutlery tray
(select models)
3 Upper basket
4 Water feed for
the middle spray arm
5 Middle spray arm
6 Lower spray arm7 Four height adjustable feet
8 Triple Filter System
9 Salt reservoir
10 Detergent dispenser
11 Rinse aid reservoir
(with dosage selector)
12 Data plate
Guide to the dishwasher
11 

Control panel
13 On/Off button
14 Program list / indicators
15 Check / Refill indicators
16 Program sequence display
17 Start/Stop button18 Top Solo button
19 Program selection buttons
20 Child Safety Lock
21 Door release
22 Drying vent
Every dishwasher is tested before leaving the factory. Any water remaining in
the machine is from these tests and does not indicate that the machine has
been used.
Guide to the dishwasher
12 

To open the door
^Press the release catch inside the
door grip.
If the door is opened during operation,
the dishwasher will stop running. Once
the door is closed the program will
restart.
To close the door
^Push the baskets in.
^
Lift the door and push until it clicks
into position.
Child Safety Lock
The yellow key for the Child Safety
Lock is shipped on one of the spikes
at the front of the upper basket.
Remove the key before using the
dishwasher.
The Child Safety Lock is designed to
prevent children...

Water softener
To achieve good cleaning results, the
dishwasher needs soft water. Hard
water results in calcium deposits on
dishware and in the dishwasher.
If your tap water hardness is above
8 gr/gal (values are in US gallons)
(140 ppm), the water should be
softened. This takes place
automatically in the unit’s integrated
water softener.
–Your local water authority will be able
to advise you of the water hardness
level in your area.
– The dishwasher must be
programmed to correspond to the
water hardness...

Programming the water softener
Your water hardness level must be
programmed into the dishwasher using
the buttons on the control panel.
^Make sure the dishwasher is turned
off.
^Press and hold the Start/Stop button
(17) and at the same time turn on the
dishwasher with the On/Off button
(13). Release the Start/Stop button
within two seconds.
The Rinse (16) indicator and a
program indicator will light and the
Salt (15) indicator will flash.
If this is not the case, the above steps
must be repeated.
If your...

23 - 70 gr/gal:
^Press the program seletion button%
(19) until the Rinse (16) indicator
flashes.
This is the second program level.
^Use the program selection buttons
(19) to select the program which
corresponds to the water hardness in
your area.
Table 2
gr/gal ppm Program indicator
23 - 35 410 - 630 Pots & Pans
36 - 70 650 - 1260 Sani Wash
The selected program indicator (14)
and the Rinse (16) indicator will flash.
To store the programmed water
hardness:
^Press the Start/Stop button (17)
twice.
^
Turn...

Filling the salt reservoir
If your water hardness level is greater
than 8 gr/gal, the salt reservoir should
be filled before the first use and when
the Salt indicator lights.
Only use water softener salt specially
formulated for dishwashers. Other salts
may contain insoluble additives which
can impair the water softener.
The proper salt can be purchased from
your Miele dealer or Miele’s Technical
Service Department.
,Inadvertently filling the salt
reservoir with dishwashing
detergent will damage the...

Salt indicator
When the salt reservoir is empty, the
Salt-PC indicator will light, indicating
that it should be refilled with
reactivation salt.
After the reservoir has been filled, the
water softener is automatically
reactivated the next time the
dishwasher is started. The Salt
indicator will be lit during this process.Bypassing the salt indicator
If your water is soft (below 8 gr/gal) the
salt reservoir should not be filled with
salt. The indicator will remain lit and
should be disregarded or...

Rinse aid
Rinse aid is recommended to prevent
spotting on dishes and glassware.
,Filling the rinse aid reservoir with
detergent will damage the reservoir.
Only pour rinse aid formulated for
residential dishwashersinto the
reservoir.
Adding rinse aid
^
Add rinse aid before the first use and
whenever the Rise aid indicator
lights.
^
Press the button in the direction of
the arrow until the flap springs open.^Pour liquid rinse aid into the reservoir
until it is visible on the surface of the
screen.
^Press on...

Adjusting the dosage
The dosage selector is preset to 3. This
dispenses  approximately 3 ml of rinse
aid per program. It can be adjusted
from 1 to 6.
^Use a higher setting if spots appear
on dry glassware.
^Use a lower setting if streaking
appears on dishes or glasses.
Rinse aid indicator
The rinse aid indicator on the control
panel will light when the rinse aid
reservoir needs refilling.
When the indicator first comes on, there
will be enough rinse aid left for 2 - 3
washes.
Before using for the first...