Miele G 7883 User Manual

INSTALLATION INSTRUCTIONS 

Disposal of the packing
material
The protective packing materials are
environmentally safe and can be
recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Disposal of the appliance
Appliances contain materials which can
be recycled. Please contact your local
authorities about recycling in your area.
Ensure that the machine presents no
danger to children while being stored
for disposal. See Important Safety...

Please refer to the installation
diagram supplied with the machine.
,Furniture and fittings installed
near the machine must be of a
commercial standard (able to
withstand the effects of steam).
Installation options
–Free-standing
–Undercounter
The machine can be installed under a
continuous counter or sink drain. The
recess must be at least 60 cm wide,
60 cm deep and 82 cm high.
Positioning and securing the
machine
To ensure stability, the machine must be
aligned and screwed to the counter.
^Open the...

Removing the lid (if necessary)
If necessary, remove the lid from the
machine to make installation possible.
^Open the door.
^Remove the fixing screws on the left
and right sides using a phillipshead
screwdriver.
^Pull the machine lid approx. 5 mm
forwards, lift it upwards and remove.Important for machines with steam
condenser (depending on model)
^To prevent countertop damage by
steam, the supplied self adhesive
protective foil (25 x 58 cm) must be
placed underneath the countertop
near the steam...

Water inlet
^The machine must be connected to
the water supply in accordance with
local and national regulations.
^The washer is constructed so it may
be connected to a supply without an
extra non-return valve, unless
required by code.
^An acceptable water pressure (flow
rate) is 10 - 147 psi. However, the
recommended pressure is
25 - 60 psi.
If the water pressure is below 30 psi,
the fill time will take longer.
If the Fill/Drain fault code F..E is
displayed, contact the Technical
Service Department....

DI-Water connection
The machine comes with a standard
connection for a pressure-resistant
system. The recommended water
pressure (flow rate) is 25 - 60 psi
however, water pressure of 10 - 147 psi
is acceptable.
^The DI pressure-tested hose (marked
H
2O pure) with a3/4 hose thread
must be connected to the on-site
water valve for DI purified water.
If the DI water connection is not
used, the electronics needs to be
reprogrammed by a Miele technician.
The water intake hose remains at the
rear side of the...

Drainage
^The drainage system is fitted with a
non-return valve which prevents dirty
water from flowing back into the
machine via the drain hose.
^The machine should preferably be
connected to aseparatedrainage
system onsite.
If separate drainage is not available
contact your Miele application
specialist for advice.
The onsite drain connection point
should be located between 1 ft.
(0.3 m) and 3 ft. (1 m)above the
lower edge of the machine.
If it is lower than 1 ft. (0.3 m), lay the
hose in a curve at a...

,All electrical work must be
performed by a qualified person in
accordance with local and national
safety regulations.
The machine comes equipped for
connection to a 208 V, 60 Hz, 3 phase
power supply. It is equipped with a 6 ft.
long, 12/4 AWG power cord, without a
plug. A plug, rated for the required
power which will fit the receptacle, is to
be supplied by the electrician doing the
installation. It should be connected to
the main power supply.
Voltage: 208 V, 3 phase
Frequency: 60 Hz
Rated Load: 6 kW...

Grounding connection
^The ground lead must be connected
to the screw connection point
(marked with the ground symbol8) at
the back of the machine.
The machine must only be operated
with the voltage, frequency and
fusing shown on thedata plate
located on the rear of the machine,
and on the plinth (behind the service
panel).
Theconversion diagramand the
wiring diagramis secured to the inner
side of the service panel.
Removing the service panel
Disconnect the machine from the
main electrical supply.
^Remove...

English Metric
Height: 33
7/16 (325/16) 85 (82) cm
Width: 23
5/8 60 cm
Depth: 23
5/8 60 cm
Voltage: 208 V
Power cord approx. 5’ 11 1.8 m
Water pressure (flow rate):
Recommended 25 - 60 psi 1.72 - 4.13 bar
Acceptable 10 - 147 psi .7 - 10 bar
Cold or Hot water
connection up to max. 158°F 70 °C
DI-Water connection
Recommended 25 - 60 psi 1.72 - 4.13 bar
Acceptable 10 - 147 psi .7 - 10 bar
Delivery head: min. 12 0.3 m
max. 39
3/81 m
Drainage length: max. 13’ 1 4 m
Water intake hose approx. 5’ 7 1.7 m
Drain...