Miele G 7883 User Manual

Turning on
^Close the door.
^Press the On/Off button.
When the program selector is at the
Stopfposition, a point lights up in
the display.
Starting a program
^Turn the program selector clockwise
or counterclockwise to the required
program.
The temperature of the first rinse of
the program selected (except for
Pre-Wash and Drain) is shown in
the display. The Start indicator will
flash.
^
Select the Drying0function if
required (see Drying).
^
Press the Start6button. The actual
temperature will appear in...

Drying
Drying0may be selected as an
additional feature once a program has
been selected (except in the Rinse
and Drain programs).
Drying is phased over 10 minutes. The
total running time of the program
lengthens accordingly.
Changing a program
A wrongly selected program may be
changed as described below.
If the "Start"6button has not yet
been pressed
^Turn the program selector to the
required program.
^Select the Drying0function if
required (see Drying).
^Press the Start6button.
If...

Canceling a program
^Turn the program selector to the
Stopfposition (the program will
stop after approximately 2 seconds).
^Open the door.
,Caution: Water and items in the
machine may be hot. Danger of
burning or scalding.
^Arrange the load securely. Wear
protective gloves where necessary,
and observe appropriate health and
safety regulations relating to
infectious diseases.
^Replenish powder detergent, if
necessary.
^Close the door.
^Select and start the Drain program.
^When finished with Drain, select...

For future servicing, please
document any alterations to the
standard factory settings.
General note
Program selector positions that have
not been allocated to a function are
indicated in the middle part of the
display by a bar (-).
The programming level is called up via
the Stopfposition.
Accessing the programming
level
Before performing any of the special
functions that follow, the programming
mode of the labwasher controller needs
to be accessed.
^Turn the program selector to Stop
f.
^Turn the machine...

1. Setting the dosage
concentration and priming the
dosage system
Before performing any of the
following special functions, the
programming mode of the controller
needs to be accessed. See
Accessing the programming level.
1.1 DOS 1 (Liquid detergent)
by DOS unit G 60 or C 60 (Optional
accessory)
1.1.1 Setting the dosage
concentration
^Access the programming level E02 of
the controller (see Accessing the
programming level).
Set the dosage concentration
according to the detergent
manufacturer’s...

1.1.2 Priming the detergent system
a) If the dosage concentration is set:
^Turn the program selector to
Custom. do1 appears in the
display.
^Press the Displayßbutton.
The dosage system will be primed
automatically. The priming is done if
the display shows 0.
To store the settings:
^Press the Start6button. SP
appears in the display.
^Press the Start6button again. The
change has been saved.b) If the system is primed only (e.g.
because the dosage system was
completely empty):
^Select programming level E02...

Before performing any of the
following special functions, the
programming mode of the controller
needs to be accessed.
1.2 DOS 3 (Neutralizer)
1.2.1 Setting the dosage concentration
The dosage is factory set at 0.10, you
may or may not be required to adjust it.
Set the dosage concentration
according to the detergent
manufacturer’s recommendations.
Example:
The manufacturer recommends a
neutralizer concentration of 0.3 %.
The value to be set is 0.30.
^First access the programming level
E02.
^Turn the...

2. Changes in wash temperature
and / or temperature holding
time at "Main wash" (except
SPECIAL 93°C-10’ and "Final
rinse")
Any changes to the wash
temperature and/or the temperature
holding time should be recorded in
the appropriate section of the
Program guide.
The factory setting of the cleaning and
final rinse temperature with temperature
holding time can be seen in the
Program guide.
The cleaning and final rinse
temperature can be changed from 30
°C - 93 °C and 30 °C - 70 °C...

"Main wash" temperature
^Main wash 1:
Press and hold the Drying0
button until E09 appears in the
display.
Main wash 2:
Press and hold the Drying0
button until E12 appears in the
display.
^Turn the program selector to the
program to be changed. The current
value appears in the display after°C.
^Press and hold Displayßuntil the
desired value appears in the display.
To store settings
^Press the Start6button. SP
appears in the display.
^Press the Start6button again. The
change has been...

"Final rinse" temperature
^Turn the program selector to STOP
f.
^Final rinse 1:
Press and hold Drying0until E22
appears in the display.
Final rinse 2:
Press and hold Drying0until E25
appears in the display.
^Turn the program selector back to the
program to be changed. The current
value appears in the display after°C.
^Press and hold Displayßuntil the
desired value appears in the display.
To store settings
^Press the Start6button. SP
appears in the display.
^Press the Start6button again. The...